90 degree grinding machine

glen mills powder mixing, milling, and particle reduction

The mixing basket can hold any form of container having a maximum volume of 2 liters. The containers are fastened in place by twisted rubber rings. The basket movement is driven by elastic drive belts and an eccentric drive gear. The speed can be varied by adjusting the position of the drive belts on its 5 step pulleys. The speed can also be adjusted optional frequency converter set up next to the machine.

The mixing basket can hold up to 66 pounds in a 17 liter container. Twisted rubber clamping rings allow the use of smaller containers up to a maximum diameter of 220 mm. The movement of the mixing basket is controlled by a silent pendulum chain drive. The speed can be varied by adjusting the position of the round drive belt on the 4-step pulley.

The mixing basket can hold up to 165 pounds in a 55 liter container. Special holders must be mounted for smaller containers. These inserts are custom designed to fit the dimensions of your mixing vessel. The movement of the mixing basket is controlled by a silent pendulum chain drive and the speed can be varied by adjusting the position of the V-belt on the 5-step pulley. An extra slow speed drive is used to bring the mixing basket into its loading position. A hand cart can be purchased to help with loading.

Model equipped for both high speed revolution and a wide radius gyration, supporting for the production of high quality materials. The timing by which the revolving speed of rotation increases is controlled to improve the mixing rate of powders and liquids and sustains the generation of lumps.

90 different revolution-rotation speed patterns are available by varying the ratio of revolution and rotation. A high function model for covering from research and development to small-scale production.

A model with a vacuum reduced pressure function suited for medium-scale production. The individual revolution and rotation speed control system and wide radius gyration generate centrifugal force even at low revolving speeds, sustaining material of thermal elevation and composition change.

A high function model with a vacuum reduced pressure function. The individual revolution and rotation speed control system and the shifted cup tray enhance mixing performance and provide effective degassing.

A jet mill grinds materials by using a high speed jet of compressed air or inert gas to impact particles into each other. Jet mills can be designed to output particles below a certain size, while continue milling particles above that size, resulting in a narrow size distribution of the resulting product. Particles leaving the mill can be separated from the gas stream by cyclonic separation.

With two sharp, robust blades and apowerful 1000 W motor, it is ideal for homogenizing substances with a high water, oil or fat content as well as for grinding dry, soft and medium-hard products. Awide selection of lids and containersallows for adaptation of the mill toindividual application requirements. The GRINDOMIX GM 200 meets andexceeds all special laboratory and analytical requirementsand is a professional device superior to any commercial household mixer.

The mixer mill MM 200 is a compact versatile benchtop unit, which has been developed specially for dry grinding of small amounts of sample. It can mix and homogenize powders in only a few seconds. It is also perfectly suitable for the disruption of biological cells as well as for DNA/RNA extraction.

You may also be interested in theHigh Energy Ball Mill Emax, an entirely new type of mill for high energy input. The unique combination of high friction and impact results in extremely fine particles within the shortest amount of time.

With itsadjustable speedof 3,000 to 10,000 rpm the rotor beater mill SR 300 is intended foruniversal use: from sample preparation in laboratories up to preparing sample batches in pilot plants or production facilities. The grinding chamber, the feed hopper and the material inlet are completely made fromhigh quality stainless steel.

The SM 100 is thebudget-priced basic model among the cutting mills. With its strong 1.5 kW drive and 1,500 rpm rotor speed the mill is particularlysuitable for routine applications. Cleaning is made particularly easy.

In combination with the wide choice of bottom sieves, hoppers and collecting vessels, the mill can be easily adapted to varying application requirements. The SM 100 can be bench-mounted; alternatively a convenient base frame on wheels is available.

Cutting mills are suitable for thegrinding of soft, medium-hard, elastic, fibrous, and heterogeneous mixes of products.The new cutting mill SM 200 is a powerful and easy-to-operate instrument for efficient primary and fine size reduction.Cleaning is made particularly easy.

Within the group of the cutting mills, it is the universal standard modelwhichcovers a vast range of applicationswith its strong 2.2 kW drive and 1,500 rpm rotor speed.When operated with theoptional cyclone-suction-combination, the SM 200 is also suitable for grinding light sample materials or smaller quantities. In combination with the wide choice of bottom sieves, hoppers and collecting vessels, the mill can be easily adapted to varying application requirements.

Cutting mills are suitable for thegrinding of soft, medium-hard, tough, elastic, fibrous, and heterogeneous mixes of products.The new Cutting Mill SM 300excels especially in the tough jobswhere other cutting mills fail.

Thehigh torqueof the new 3 kW drive withRES technology(additional flywheel mass) allows for an exceptionally effective preliminary size reduction of heterogeneous mixtures, such as waste or electronic components. Analytical fineness is often achieved in one working run.

The cutting mill is used successfully for a great variety of materials. The sample is only moderately warmed up during the grinding process so that the mill is perfectly suitable forgrinding temperature-sensitive materials.Another innovation is the wide, freelyselectable speed range from 100 to 3,000 min-1.

When operated with theoptional cyclone-suction-combination, the SM 300 is also suitable for grinding light sample materials or smaller quantities. In combination with the wide choice of bottom sieves, hoppers and collecting vessels, the mill can be easily adapted to varying application requirements.

Cutting mills are suitable for thegrinding of soft, medium-hard, tough, elastic, fibrous, and heterogeneous mixes of products.The Cutting Mill SM 400 is ideally suited for pre-cutting of large sample pieces but, depending on the application, may also achieve the required fineness in one step.

The cutting mill is used successfully for a great variety of materials. The sample is only moderately warmed up during the grinding process so that the mill is perfectlysuitable for grinding temperature-sensitive materials.Due to the large open surface of the 240 mm x 240 mm bottom sieve, it is possible to grind large sample quantities and to increase the throughput.

When operated with theoptional cyclone-suction-combination, the SM 400 is also suitable for grinding light sample materials. In combination with the wide choice of bottom sieves, hoppers and collecting vessels, the mill can be easily adapted to varying application requirements.

Analysis or quality control requires finely ground samples. Easy to change grinding attachments and sieves extend the range of any samples that can be processed. Simple handling, high user safety and efficient grinding results are just a few of the advantages of this mill.

The fluid bed dryer TG 200 is used in quality control, sample preparation and R&D departments. It permits thegentle dryingof organic, inorganic, chemical or pharmaceutical bulk materialswithout localized overheating.Suitable materials can be coarse, fine, crystalline, fibrous or leafy. The powerful fan of the fluid bed dryer ensuresoptimal air throughputso that the products to be dried are loosened up and thoroughly mixed resulting inshort drying times.With the interval operation the fluidized bed is mixed even better. Temperature, drying time and air volume can be set digitally and adjusted continuously.

The PP 35 features an individual pressure force regulation in the range of 0 to 35 t. The PP 35 combines the advantage of a small bench top model with high press forces, which are built automatically in up to three steps, ensuring that even difficult materials are pressed perfectly.

The ultrasonic bath range UR includes three sizes forcleaning test sieves and grinding tools quickly and easily.UR 1 is for test sieves up to 203 mm dia., UR 2 for test sieves up to 450 mm dia., and the UR 3 for the simultaneous cleaning of up to 5 test sieves 200/203 mm dia. The gentle yet thorough cleaning of test sieves in an ultrasonic bathincreases their working livesas damage which could occur during manual cleaning is avoided.

The vibratory feeder DR 100 is used for theuniform, continuous feeding and conveyance of pourable bulk materials and fine powders. The DR 100 feeds mills, sample dividers, and particle measuring devices, and it is also suitable for other feeding tasks. Its performance, adaptability and compact design makes this device suitable for agreat variety of applications.The DR 100 can also bedriven and controlled externallyvia the built-in interface. Vibratory feeders guarantee reproducibly exact resultsand maximize the efficiency of downstream laboratory and testing devices.

Afaultless and comparable analysis is closely linked to an accurate sample handling.Only a sample representative of the initial material can provide meaningful analysis results. Sample splittersensure the representativeness of a sample and thus the reproducibility of the analysis.

The RT 100 is equipped with a feed hopper with closed outlet. Thus,up to 30 l sample materialmay be evenly spread over the entire width of the hopper. The outlet is opened manually by moving a lever and the sample is splitted. The slots of the dividing head can be adjusted to a maximum width of 108 mm.

Solid, high-quality pellets are an important precondition for reliable and meaningful XRF analysis. The PP 25 is a compact benchtop unit with particularlysimple and safe operation.With apressure force of 25 tit is ideally suited for thepreparation of solid samples for XRF analysis.The pellets produced are ofhigh qualityand are characterized by theirhigh degree of stability.The piston pressure can be read off from the clearly visible manometer scale. The dies for the Pellet Press PP 25 are available in several diameters and can be evacuated completely.

The well-proven RETSCH sieves consist of a solid stainless steel sieve frame of high stability for reliable sieving results. Paying close attention to mesh-specific requirements, the sieve fabric is precisely joined into the frame and tautened. RETSCH test sieve provides a clear and accurate labeling with full traceability.

The sieves can be easily combined with all other sieve brands. Each sieve that leaves our company comes with a test report or, at your request, with a special inspection certificate in conformity withnational and international standards (PDF). RETSCH calibration certificates confirm a great number of precision measurements, thus ensuring an even higher statistical reliability for your quality control.

The well-proven RETSCH sieves consist of a solid stainless steel sieve frame of high stability for reliable sieving results. Paying close attention to mesh-specific requirements, the sieve fabric is precisely joined into the frame and tautened. The individual laser engraving of each RETSCH test sieve provides a clear and accurate labeling with full traceability.

The sieves can be easily combined with all other sieve brands. Each sieve that leaves the company comes with a test report or, at your request, with a special inspection certificate in conformity with national and international standards (PDF). RETSCH calibration certificates confirm a great number of precision measurements, thus ensuring an even higher statistical reliability for your quality control.

The vibratory sieve shakers of the series AS 200 are used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after short sieving times.

The analytical sieve shakers of the series AS 200 are used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after very short sieving times.

With its all-digital controls, up to 99 sieving programs and calibration certificate the sieve shaker AS 200 control is indispensable for all users who attach importance to precision and operational convenience and need to comply with the guidelines of the ISO 9001.

The analytical sieve shakers of the series AS 200 are used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after short sieving times.

The new Air Jet Sieve AS 200 jet is particularly suitable for sieve cuts of powdered materials which require efficient dispersion and deagglomeration. The option to store up to 10 SOPs and the automatic vacuum regulator (accessory) guarantees reproducible and meaningful results.

The analytical sieve shaker AS 200 tap is used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. Its tapping motion supports the sieve analysis of certain products such as activated carbon, abrasives, metal powder, spices and diamonds, as specified in the corresponding standards.

The analytical sieve shaker AS 300 control is used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after short sieving times.

The AS 300 control is particularly designed for test sieves with a diameter of 305 mm (12). Compared to sieves with a diameter of 200 mm, a 2.25 times higher sieving surface is available. Therefore, the average sieving times can be greatly reduced with the AS 300 control. With its all-digital controls and calibration certificate the sieve shaker AS 300 control is indispensable for all users who attach importance to precision and operational convenience and need to comply with the guidelines of the ISO 9001.

The AS 400 control is used for the sieving of dry goods with test sieves of a diameter up to 400 mm. In this, the uniform, horizontal circular motion ensures exact separation of fine and coarse-grained products.

With its all-digital controls and calibration certificate the AS 400 control is indispensable for all users who attach importance to precision and operational convenience and need to comply with the guidelines of the ISO 9001.

The AS 450 basic, is a budget-priced alternative to the AS 450 control sieve shaker. The new sieve shaker covers a size range from 25 m to 125 mm and accepts loads of up to 15 kg. Time and amplitude are digitally set, a memory function allows storage of one program. The AS 450 basic is suitable for dry and wet sieving. It is the economic solution for customers who need to sieve larger quantities of dry material with reliable results.

The analytical sieve shaker AS 450 control is used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtainable even after very short sieving times.

With the sieve shaker AS 450 control RETSCH have designed their first sieve shaker for 400 mm and 450 mm sieves which operates with a three-dimensional sieving motion. It can be used for dry and wet sieving. The optimized electromagnetic drive technology allows for an amplitude up to 2.2 mm even with maximum loads up to 25 kg. This makes the AS 450 superior to all other known sieve shakers based on conventional electromagnetic or imbalance drives.

grinding cylpebs

Our automatic production line for the grinding cylpebs is the unique. With stable quality, high production efficiency, high hardness, wear-resistant, the volumetric hardness of the grinding cylpebs is between 60-63HRC,the breakage is less than 0.5%. The organization of the grinding cylpebs is compact, the hardness is constant from the inner to the surface. Now has extensively used in the cement industry, the wear rate is about 30g-60g per Ton cement.

Grinding Cylpebs are made from low-alloy chilled cast iron. The molten metal leaves the furnace at approximately 1500 C and is transferred to a continuous casting machine where the selected size Cylpebs are created; by changing the moulds the full range of cylindrical media can be manufactured via one simple process. The Cylpebs are demoulded while still red hot and placed in a cooling section for several hours to relieve internal stress. Solidification takes place in seconds and is formed from the external surface inward to the centre of the media. It has been claimed that this manufacturing process contributes to the cost effectiveness of the media, by being more efficient and requiring less energy than the conventional forging method.

Because of their cylindrical geometry, Cylpebs have greater surface area and higher bulk density compared with balls of similar mass and size. Cylpebs of equal diameter and length have 14.5% greater surface area than balls of the same mass, and 9% higher bulk density than steel balls, or 12% higher than cast balls. As a result, for a given charge volume, about 25% more grinding media surface area is available for size reduction when charged with Cylpebs, but the mill would also draw more power.

home | brown tool & machine co., inc

Brown Tool & Machine Company, Inc. is a leading custom machine shop with over three decades of experience in machine metal services. We are specialists in performance outboard motor racing parts and accessories and invite you to browse our current inventory of over 100 performance marine products. We also welcome you to contact us to discuss your next custom machining project.

Prior to ordering please call 609-397-1751 to setup payment information. For your convenience, once we have all of your pertinent information in our secure file, you may use our online ordering system 24/7. (Note: it is your responsibility to keep this information current)

The user shall determine the suitability of the product for his or her intended use and shall assume all risk and liability in connection therewith; this will include all items sold by Brown Tool & Machine Co., Inc. or its authorized dealers and suppliers.