In all ore dressing and milling Operations, including flotation, cyanidation, gravity concentration, and amalgamation, the Working Principle is to crush and grind, often with rob mill & ball mills, the ore in order to liberate the minerals. In the chemical and process industries, grinding is an important step in preparing raw materials for subsequent treatment.In present day practice, ore is reduced to a size many times finer than can be obtained with crushers. Over a period of many years various fine grinding machines have been developed and used, but the ball mill has become standard due to its simplicity and low operating cost.
A ball millefficiently operated performs a wide variety of services. In small milling plants, where simplicity is most essential, it is not economical to use more than single stage crushing, because the Steel-Head Ball or Rod Mill will take up to 2 feed and grind it to the desired fineness. In larger plants where several stages of coarse and fine crushing are used, it is customary to crush from 1/2 to as fine as 8 mesh.
Many grinding circuits necessitate regrinding of concentrates or middling products to extremely fine sizes to liberate the closely associated minerals from each other. In these cases, the feed to the ball mill may be from 10 to 100 mesh or even finer.
Where the finished product does not have to be uniform, a ball mill may be operated in open circuit, but where the finished product must be uniform it is essential that the grinding mill be used in closed circuit with a screen, if a coarse product is desired, and with a classifier if a fine product is required. In most cases it is desirable to operate the grinding mill in closed circuit with a screen or classifier as higher efficiency and capacity are obtained. Often a mill using steel rods as the grinding medium is recommended, where the product must have the minimum amount of fines (rods give a more nearly uniform product).
Often a problem requires some study to determine the economic fineness to which a product can or should be ground. In this case the 911Equipment Company offers its complete testing service so that accurate grinding mill size may be determined.
Until recently many operators have believed that one particular type of grinding mill had greater efficiency and resulting capacity than some other type. However, it is now commonly agreed and accepted that the work done by any ballmill depends directly upon the power input; the maximum power input into any ball or rod mill depends upon weight of grinding charge, mill speed, and liner design.
The apparent difference in capacities between grinding mills (listed as being the same size) is due to the fact that there is no uniform method of designating the size of a mill, for example: a 5 x 5 Ball Mill has a working diameter of 5 inside the liners and has 20 per cent more capacity than all other ball mills designated as 5 x 5 where the shell is 5 inside diameter and the working diameter is only 48 with the liners in place.
Ball-Rod Mills, based on 4 liners and capacity varying as 2.6 power of mill diameter, on the 5 size give 20 per cent increased capacity; on the 4 size, 25 per cent; and on the 3 size, 28 per cent. This fact should be carefully kept in mind when determining the capacity of a Steel- Head Ball-Rod Mill, as this unit can carry a greater ball or rod charge and has potentially higher capacity in a given size when the full ball or rod charge is carried.
A mill shorter in length may be used if the grinding problem indicates a definite power input. This allows the alternative of greater capacity at a later date or a considerable saving in first cost with a shorter mill, if reserve capacity is not desired. The capacities of Ball-Rod Mills are considerably higher than many other types because the diameters are measured inside the liners.
The correct grinding mill depends so much upon the particular ore being treated and the product desired, that a mill must have maximum flexibility in length, type of grinding medium, type of discharge, and speed.With the Ball-Rod Mill it is possible to build this unit in exact accordance with your requirements, as illustrated.
To best serve your needs, the Trunnion can be furnished with small (standard), medium, or large diameter opening for each type of discharge. The sketch shows diagrammatic arrangements of the four different types of discharge for each size of trunnion opening, and peripheral discharge is described later.
Ball-Rod Mills of the grate discharge type are made by adding the improved type of grates to a standard Ball-Rod Mill. These grates are bolted to the discharge head in much the same manner as the standard headliners.
The grates are of alloy steel and are cast integral with the lifter bars which are essential to the efficient operation of this type of ball or rod mill. These lifter bars have a similar action to a pump:i. e., in lifting the product so as to discharge quickly through the mill trunnion.
These Discharge Grates also incorporate as an integral part, a liner between the lifters and steel head of the ball mill to prevent wear of the mill head. By combining these parts into a single casting, repairs and maintenance are greatly simplified. The center of the grate discharge end of this mill is open to permit adding of balls or for adding water to the mill through the discharge end.
Instead of being constructed of bars cast into a frame, Grates are cast entire and have cored holes which widen toward the outside of the mill similar to the taper in grizzly bars. The grate type discharge is illustrated.
The peripheral discharge type of Ball-Rod Mill is a modification of the grate type, and is recommended where a free gravity discharge is desired. It is particularly applicable when production of too many fine particles is detrimental and a quick pass through the mill is desired, and for dry grinding.
The drawings show the arrangement of the peripheral discharge. The discharge consists of openings in the shell into which bushings with holes of the desired size are inserted. On the outside of the mill, flanges are used to attach a stationary discharge hopper to prevent pulp splash or too much dust.
The mill may be operated either as a peripheral discharge or a combination or peripheral and trunnion discharge unit, depending on the desired operating conditions. If at any time the peripheral discharge is undesirable, plugs inserted into the bushings will convert the mill to a trunnion discharge type mill.
Unless otherwise specified, a hard iron liner is furnished. This liner is made of the best grade white iron and is most serviceable for the smaller size mills where large balls are not used. Hard iron liners have a much lower first cost.
Electric steel, although more expensive than hard iron, has advantage of minimum breakage and allows final wear to thinner section. Steel liners are recommended when the mills are for export or where the source of liner replacement is at a considerable distance.
Molychrome steel has longer wearing qualities and greater strength than hard iron. Breakage is not so apt to occur during shipment, and any size ball can be charged into a mill equipped with molychrome liners.
Manganese liners for Ball-Rod Mills are the world famous AMSCO Brand, and are the best obtainable. The first cost is the highest, but in most cases the cost per ton of ore ground is the lowest. These liners contain 12 to 14% manganese.
The feed and discharge trunnions are provided with cast iron or white iron throat liners. As these parts are not subjected to impact and must only withstand abrasion, alloys are not commonly used but can be supplied.
Gears for Ball-Rod Mills drives are furnished as standard on the discharge end of the mill where they are out of the way of the classifier return, scoop feeder, or original feed. Due to convertible type construction the mills can be furnished with gears on the feed end. Gear drives are available in two alternative combinations, which are:
All pinions are properly bored, key-seated, and pressed onto the steel countershaft, which is oversize and properly keyseated for the pinion and drive pulleys or sheaves. The countershaft operates on high grade, heavy duty, nickel babbitt bearings.
Any type of drive can be furnished for Ball-Rod Mills in accordance with your requirements. Belt drives are available with pulleys either plain or equipped with friction clutch. Various V- Rope combinations can also be supplied.
The most economical drive to use up to 50 H. P., is a high starting torque motor connected to the pinion shaft by means of a flat or V-Rope drive. For larger size motors the wound rotor (slip ring) is recommended due to its low current requirement in starting up the ball mill.
Should you be operating your own power plant or have D. C. current, please specify so that there will be no confusion as to motor characteristics. If switches are to be supplied, exact voltage to be used should be given.
Even though many ores require fine grinding for maximum recovery, most ores liberate a large percentage of the minerals during the first pass through the grinding unit. Thus, if the free minerals can be immediately removed from the ball mill classifier circuit, there is little chance for overgrinding.
This is actually what has happened wherever Mineral Jigs or Unit Flotation Cells have been installed in the ball mill classifier circuit. With the installation of one or both of these machines between the ball mill and classifier, as high as 70 per cent of the free gold and sulphide minerals can be immediately removed, thus reducing grinding costs and improving over-all recovery. The advantage of this method lies in the fact that heavy and usually valuable minerals, which otherwise would be ground finer because of their faster settling in the classifier and consequent return to the grinding mill, are removed from the circuit as soon as freed. This applies particularly to gold and lead ores.
Ball-Rod Mills have heavy rolled steel plate shells which are arc welded inside and outside to the steel heads or to rolled steel flanges, depending upon the type of mill. The double welding not only gives increased structural strength, but eliminates any possibility of leakage.
Where a single or double flanged shell is used, the faces are accurately machined and drilled to template to insure perfect fit and alignment with the holes in the head. These flanges are machined with male and female joints which take the shearing stresses off the bolts.
The Ball-Rod Mill Heads are oversize in section, heavily ribbed and are cast from electric furnace steel which has a strength of approximately four times that of cast iron. The head and trunnion bearings are designed to support a mill with length double its diameter. This extra strength, besides eliminating the possibility of head breakage or other structural failure (either while in transit or while in service), imparts to Ball-Rod Mills a flexibility heretofore lacking in grinding mills. Also, for instance, if you have a 5 x 5 mill, you can add another 5 shell length and thus get double the original capacity; or any length required up to a maximum of 12 total length.
On Type A mills the steel heads are double welded to the rolled steel shell. On type B and other flanged type mills the heads are machined with male and female joints to match the shell flanges, thus taking the shearing stresses from the heavy machine bolts which connect the shell flanges to the heads.
The manhole cover is protected from wear by heavy liners. An extended lip is provided for loosening the door with a crow-bar, and lifting handles are also provided. The manhole door is furnished with suitable gaskets to prevent leakage.
The mill trunnions are carried on heavy babbitt bearings which provide ample surface to insure low bearing pressure. If at any time the normal length is doubled to obtain increased capacity, these large trunnion bearings will easily support the additional load. Trunnion bearings are of the rigid type, as the perfect alignment of the trunnion surface on Ball-Rod Mills eliminates any need for the more expensive self-aligning type of bearing.
The cap on the upper half of the trunnion bearing is provided with a shroud which extends over the drip flange of the trunnion and effectively prevents the entrance of dirt or grit. The bearing has a large space for wool waste and lubricant and this is easily accessible through a large opening which is covered to prevent dirt from getting into the bearing.Ball and socket bearings can be furnished.
Scoop Feeders for Ball-Rod Mills are made in various radius sizes. Standard scoops are made of cast iron and for the 3 size a 13 or 19 feeder is supplied, for the 4 size a 30 or 36, for the 5 a 36 or 42, and for the 6 a 42 or 48 feeder. Welded steel scoop feeders can, however, be supplied in any radius.
The correct size of feeder depends upon the size of the classifier, and the smallest feeder should be used which will permit gravity flow for closed circuit grinding between classifier and the ball or rod mill. All feeders are built with a removable wearing lip which can be easily replaced and are designed to give minimum scoop wear.
A combination drum and scoop feeder can be supplied if necessary. This feeder is made of heavy steel plate and strongly welded. These drum-scoop feeders are available in the same sizes as the cast iron feeders but can be built in any radius. Scoop liners can be furnished.
The trunnions on Ball-Rod Mills are flanged and carefully machined so that scoops are held in place by large machine bolts and not cap screws or stud bolts. The feed trunnion flange is machined with a shoulder for insuring a proper fit for the feed scoop, and the weight of the scoop is carried on this shoulder so that all strain is removed from the bolts which hold the scoop.
High carbon steel rods are recommended, hot rolled, hot sawed or sheared, to a length of 2 less than actual length of mill taken inside the liners. The initial rod charge is generally a mixture ranging from 1.5 to 3 in diameter. During operation, rod make-up is generally the maximum size. The weights per lineal foot of rods of various diameters are approximately: 1.5 to 6 lbs.; 2-10.7 lbs.; 2.5-16.7 lbs.; and 3-24 lbs.
Forged from the best high carbon manganese steel, they are of the finest quality which can be produced and give long, satisfactory service. Data on ball charges for Ball-Rod Mills are listed in Table 5. Further information regarding grinding balls is included in Table 6.
Rod Mills has a very define and narrow discharge product size range. Feeding a Rod Mill finer rocks will greatly impact its tonnage while not significantly affect its discharge product sizes. The 3.5 diameter rod of a mill, can only grind so fine.
Crushers are well understood by most. Rod and Ball Mills not so much however as their size reduction actions are hidden in the tube (mill). As for Rod Mills, the image above best expresses what is going on inside. As rocks is feed into the mill, they are crushed (pinched) by the weight of its 3.5 x 16 rods at one end while the smaller particles migrate towards the discharge end and get slightly abraded (as in a Ball Mill) on the way there.
We haveSmall Ball Mills for sale coming in at very good prices. These ball mills are relatively small, bearing mounted on a steel frame. All ball mills are sold with motor, gears, steel liners and optional grinding media charge/load.
Ball Mills or Rod Mills in a complete range of sizes up to 10 diameter x20 long, offer features of operation and convertibility to meet your exactneeds. They may be used for pulverizing and either wet or dry grindingsystems. Mills are available in both light-duty and heavy-duty constructionto meet your specific requirements.
All Mills feature electric cast steel heads and heavy rolled steelplate shells. Self-aligning main trunnion bearings on large mills are sealedand internally flood-lubricated. Replaceable mill trunnions. Pinion shaftbearings are self-aligning, roller bearing type, enclosed in dust-tightcarrier. Adjustable, single-unit soleplate under trunnion and drive pinionsfor perfect, permanent gear alignment.
Ball Mills can be supplied with either ceramic or rubber linings for wet or dry grinding, for continuous or batch type operation, in sizes from 15 x 21 to 8 x 12. High density ceramic linings of uniform hardness male possible thinner linings and greater and more effective grinding volume. Mills are shipped with liners installed.
Complete laboratory testing service, mill and air classifier engineering and proven equipment make possible a single source for your complete dry-grinding mill installation. Units available with air swept design and centrifugal classifiers or with elevators and mechanical type air classifiers. All sizes and capacities of units. Laboratory-size air classifier also available.
A special purpose batch mill designed especially for grinding and mixing involving acids and corrosive materials. No corners mean easy cleaning and choice of rubber or ceramic linings make it corrosion resistant. Shape of mill and ball segregation gives preferential grinding action for grinding and mixing of pigments and catalysts. Made in 2, 3 and 4 diameter grinding drums.
Nowadays grinding mills are almost extensively used for comminution of materials ranging from 5 mm to 40 mm (3/161 5/8) down to varying product sizes. They have vast applications within different branches of industry such as for example the ore dressing, cement, lime, porcelain and chemical industries and can be designed for continuous as well as batch grinding.
Ball mills can be used for coarse grinding as described for the rod mill. They will, however, in that application produce more fines and tramp oversize and will in any case necessitate installation of effective classification.If finer grinding is wanted two or three stage grinding is advisable as for instant primary rod mill with 75100 mm (34) rods, secondary ball mill with 2540 mm(11) balls and possibly tertiary ball mill with 20 mm () balls or cylpebs.To obtain a close size distribution in the fine range the specific surface of the grinding media should be as high as possible. Thus as small balls as possible should be used in each stage.
The principal field of rod mill usage is the preparation of products in the 5 mm0.4 mm (4 mesh to 35 mesh) range. It may sometimes be recommended also for finer grinding. Within these limits a rod mill is usually superior to and more efficient than a ball mill. The basic principle for rod grinding is reduction by line contact between rods extending the full length of the mill, resulting in selective grinding carried out on the largest particle sizes. This results in a minimum production of extreme fines or slimes and more effective grinding work as compared with a ball mill. One stage rod mill grinding is therefore suitable for preparation of feed to gravimetric ore dressing methods, certain flotation processes with slime problems and magnetic cobbing. Rod mills are frequently used as primary mills to produce suitable feed to the second grinding stage. Rod mills have usually a length/diameter ratio of at least 1.4.
Tube mills are in principle to be considered as ball mills, the basic difference being that the length/diameter ratio is greater (35). They are commonly used for surface cleaning or scrubbing action and fine grinding in open circuit.
In some cases it is suitable to use screened fractions of the material as grinding media. Such mills are usually called pebble mills, but the working principle is the same as for ball mills. As the power input is approximately directly proportional to the volume weight of the grinding media, the power input for pebble mills is correspondingly smaller than for a ball mill.
A dry process requires usually dry grinding. If the feed is wet and sticky, it is often necessary to lower the moisture content below 1 %. Grinding in front of wet processes can be done wet or dry. In dry grinding the energy consumption is higher, but the wear of linings and charge is less than for wet grinding, especially when treating highly abrasive and corrosive material. When comparing the economy of wet and dry grinding, the different costs for the entire process must be considered.
An increase in the mill speed will give a directly proportional increase in mill power but there seems to be a square proportional increase in the wear. Rod mills generally operate within the range of 6075 % of critical speed in order to avoid excessive wear and tangled rods. Ball and pebble mills are usually operated at 7085 % of critical speed. For dry grinding the speed is usually somewhat lower.
The mill lining can be made of rubber or different types of steel (manganese or Ni-hard) with liner types according to the customers requirements. For special applications we can also supply porcelain, basalt and other linings.
The mill power is approximately directly proportional to the charge volume within the normal range. When calculating a mill 40 % charge volume is generally used. In pebble and ball mills quite often charge volumes close to 50 % are used. In a pebble mill the pebble consumption ranges from 315 % and the charge has to be controlled automatically to maintain uniform power consumption.
In all cases the net energy consumption per ton (kWh/ton) must be known either from previous experience or laboratory tests before mill size can be determined. The required mill net power P kW ( = ton/hX kWh/ton) is obtained from
Trunnions of S.G. iron or steel castings with machined flange and bearing seat incl. device for dismantling the bearings. For smaller mills the heads and trunnions are sometimes made in grey cast iron.
The mills can be used either for dry or wet, rod or ball grinding. By using a separate attachment the discharge end can be changed so that the mills can be used for peripheral instead of overflow discharge.
This ball mill is typically designed to grind mineral ores and other materials with different hardness, and it is widely used in different fields, such as ore dressing, building material field, chemical industry, etc. Due to the difference of its slurry discharging method, it is divided to two types: grid type ball mill and overflow type ball mill.
Compared with grid type ball mill, overflow type ball mill can grind materials finer even though its grinding time is usually longer. So it can make finer particle products. Hence the grid type ball mill is mainly used for primary stage of grinding while overflow type ball mill is mainly used for the secondary grinding.
Ball mill Advantages: 1Jack-up device, easy maintenance; 2The hydrostatic and hydrodynamic bearings ensure the smooth operation; 3Low speed transmission is easy for starting and maintenance; 4The oil-mist lubrication device guarantees reliable performance of bearings; 5The air clutch adopts the flexible start-up model./5According to the customer demand, manganese steel liner and wear-resistant rubber liner can be customized with good wear resistance, long service life and easy maintenance.
The grinding system uses either 'open circuit' or 'closed circuit'. In an open circuit system, the feed rate of materials is adjusted to achieve the desired fineness of the product. In a closed circuit system, coarse particles are separated from the finer ones and sent back for further grinding.
Prominer has been devoted to mineral processing industry for decades and specializes in mineral upgrading and deep processing. With expertise in the fields of mineral project development, mining, test study, engineering, technological processing.
we also supply ore washing equipment, pyro procssing equipment, filtration equipment for mines and mineral processing industry. And we also produce the equipment according to the clients drawing and requirements. The liners of ore grinding mills is a big cost in the ore grining work, so we shall do our best to extend the life span of the liners. ZJH Minerals could produce the wear-resistant liners (super-high manganese steel,high manganese steel, high chromium cast iron, alloy steel) for ore gringing mills,ball mills , AG/SAG mills, rod mills. At the same time, we could slao produce the main shaft bushing for all kind of ore grinding mills. we have the powerful ability of casting, heat treatment and machining capacity. By the strict quality and process control methods, the wear-resistant liners produced by us have the high quality and long life span. we could produce the mining mill liners and parts according to your drawings.
Track mounted core drill is especially designed for coring operation of mining and geology explore industry. Our tracked mounted core drill is adopted by the diamond rope core drilling technology. It is full hydraulic driving. The depth ability of our deep hole core drill is 600m and 1200m. We have machines in stock for quick delivery. The price is good for sale.
ZJH mainly focus on producing and supply crushers, ore grinding equipment, mineral Beneficiation equipment, laboratory and pilot scale ore dressing equipment for Mining and Mineral Processing Industry. Our aim is to work together with Mines, Mineral Beneficiation Plantsfor helping to reduce the operating cost ,to improve the operating efficiency.
Our automatic production line for the grinding cylpebs is the unique. With stable quality, high production efficiency, high hardness, wear-resistant, the volumetric hardness of the grinding cylpebs is between 60-63HRC,the breakage is less than 0.5%. The organization of the grinding cylpebs is compact, the hardness is constant from the inner to the surface. Now has extensively used in the cement industry, the wear rate is about 30g-60g per Ton cement.
Grinding Cylpebs are made from low-alloy chilled cast iron. The molten metal leaves the furnace at approximately 1500 C and is transferred to a continuous casting machine where the selected size Cylpebs are created; by changing the moulds the full range of cylindrical media can be manufactured via one simple process. The Cylpebs are demoulded while still red hot and placed in a cooling section for several hours to relieve internal stress. Solidification takes place in seconds and is formed from the external surface inward to the centre of the media. It has been claimed that this manufacturing process contributes to the cost effectiveness of the media, by being more efficient and requiring less energy than the conventional forging method.
Because of their cylindrical geometry, Cylpebs have greater surface area and higher bulk density compared with balls of similar mass and size. Cylpebs of equal diameter and length have 14.5% greater surface area than balls of the same mass, and 9% higher bulk density than steel balls, or 12% higher than cast balls. As a result, for a given charge volume, about 25% more grinding media surface area is available for size reduction when charged with Cylpebs, but the mill would also draw more power.
Claudius Peters is widely acknowledged as one of the foremost authorities on coal and mineral grinding technology. With knowledge gained in over 700 applications of our famous EM ball ring mill, we offer reliable solutions for the most extreme processing challenges.
Designed without bearings or lubrication points inside the grinding section, the EM mill remains the simplest, most reliable means available for fine grinding coal and a number of other minerals. Up to 50,000 service hours can be achieved from a single set of grinding elements. Closely coupled to grinding in a number of mineral processes, is calcining.
Claudius Peters can be your full line supplier for your gypsum processing system. The key component of this system is the calcining plant, where Claudius Peters supply a range of calcining systems customized for each application. A Claudius Peters EM Mill is at the heart of a gypsum processing system, combining the functions of grinding, drying calcining and classifying the gypsum in one unit. For fine raw materials such as synthetic gypsum sources the Horizontal Impact Calciner allows direct calcining without grinding. The Claudius Peters Homogenizer, provides better plaster quality whilst the Claudius Peters Rotary Drum Cooler will cool the product from calcining temperatures to required product temperatures for further handling.
We can also accommodate separate calcining operations for high temperature applications producing anhydrite gypsum with our flash calcining process or kettle calcining systems for specific plaster systems. This calcining and grinding process know-how linked with other Claudius Peters product lines such as stockyard systems, pneumatic conveying and dispatch systems provides a "one stop" capability.
Depending on the powerful technical and the excellent production team, JinPengMiningcan not only supply mountings and consumables forits own equipment, but also can accomplish any products customized with high efficiency and high quality. Meanwhile, relying on the thick strength of scientific prowess, JinPeng Miningwill provide you with the perfect mineral processing technology,the best selection and ratio of reagents for achieving the best recovery rate.
Max Feeding size <25mm Discharge size0.075-0.4mm Typesoverflow ball mills, grate discharge ball mills Service 24hrs quotation, custom made parts, processing flow design & optimization, one year warranty, on-site installation.
Ball mill, also known as ball grinding machine, a well-known ore grinding machine, widely used in the mining, construction, aggregate application. JXSC start the ball mill business since 1985, supply globally service includes design, manufacturing, installation, and free operation training. Type according to the discharge type, overflow ball mill, grate discharge ball mill; according to the grinding conditions, wet milling, dry grinding; according to the ball mill media. Wet grinding gold, chrome, tin, coltan, tantalite, silica sand, lead, pebble, and the like mining application. Dry grinding cement, building stone, power, etc. Grinding media ball steel ball, manganese, chrome, ceramic ball, etc. Common steel ball sizes 40mm, 60mm, 80mm, 100mm, 120mm. Ball mill liner Natural rubber plate, manganese steel plate, 50-130mm custom thickness. Features 1. Effective grinding technology for diverse applications 2. Long life and minimum maintenance 3. Automatization 4. Working Continuously 5. Quality guarantee, safe operation, energy-saving. The ball grinding mill machine usually coordinates with other rock crusher machines, like jaw crusher, cone crusher, to reduce the ore particle into fine and superfine size. Ball mills grinding tasks can be done under dry or wet conditions. Get to know more details of rock crushers, ore grinders, contact us!
Ball mill parts feed, discharge, barrel, gear, motor, reducer, bearing, bearing seat, frame, liner plate, steel ball, etc. Contact our overseas office for buying ball mill components, wear parts, and your mine site visits. Ball mill working principle High energy ball milling is a type of powder grinding mill used to grind ores and other materials to 25 mesh or extremely fine powders, mainly used in the mineral processing industry, both in open or closed circuits. Ball milling is a grinding method that reduces the product into a controlled final grind and a uniform size, usually, the manganese, iron, steel balls or ceramic are used in the collision container. The ball milling process prepared by rod mill, sag mill (autogenous / semi autogenous grinding mill), jaw crusher, cone crusher, and other single or multistage crushing and screening. Ball mill manufacturer With more than 35 years of experience in grinding balls mill technology, JXSC design and produce heavy-duty scientific ball mill with long life minimum maintenance among industrial use, laboratory use. Besides, portable ball mills are designed for the mobile mineral processing plant. How much the ball mill, and how much invest a crushing plant? contact us today! Find more ball mill diagram at ball mill PDF ServiceBall mill design, Testing of the material, grinding circuit design, on site installation. The ball grinding mill machine usually coordinates with other rock crusher machines, like jaw crusher, cone crusher, get to know more details of rock crushers, ore grinders, contact us! sag mill vs ball mill, rod mill vs ball mill
How many types of ball mill 1. Based on the axial orientation a. Horizontal ball mill. It is the most common type supplied from ball mill manufacturers in China. Although the capacity, specification, and structure may vary from every supplier, they are basically shaped like a cylinder with a drum inside its chamber. As the name implies, it comes in a longer and thinner shape form that vertical ball mills. Most horizontal ball mills have timers that shut down automatically when the material is fully processed. b. Vertical ball mills are not very commonly used in industries owing to its capacity limitation and specific structure. Vertical roller mill comes in the form of an erect cylinder rather than a horizontal type like a detachable drum, that is the vertical grinding mill only produced base on custom requirements by vertical ball mill manufacturers. 2. Base on the loading capacity Ball mill manufacturers in China design different ball mill sizes to meet the customers from various sectors of the public administration, such as colleges and universities, metallurgical institutes, and mines. a. Industrial ball mills. They are applied in the manufacturing factories, where they need them to grind a huge amount of material into specific particles, and alway interlink with other equipment like feeder, vibrating screen. Such as ball mill for mining, ceramic industry, cement grinding. b. Planetary Ball Mills, small ball mill. They are intended for usage in the testing laboratory, usually come in the form of vertical structure, has a small chamber and small loading capacity. Ball mill for sale In all the ore mining beneficiation and concentrating processes, including gravity separation, chemical, froth flotation, the working principle is to prepare fine size ores by crushing and grinding often with rock crushers, rod mill, and ball mils for the subsequent treatment. Over a period of many years development, the fine grinding fineness have been reduced many times, and the ball mill machine has become the widest used grinding machine in various applications due to solid structure, and low operation cost. The ball miller machine is a tumbling mill that uses steel milling balls as the grinding media, applied in either primary grinding or secondary grinding applications. The feed can be dry or wet, as for dry materials process, the shell dustproof to minimize the dust pollution. Gear drive mill barrel tumbles iron or steel balls with the ore at a speed. Usually, the balls filling rate about 40%, the mill balls size are initially 3080 cm diameter but gradually wore away as the ore was ground. In general, ball mill grinder can be fed either wet or dry, the ball mill machine is classed by electric power rather than diameter and capacity. JXSC ball mill manufacturer has industrial ball mill and small ball mill for sale, power range 18.5-800KW. During the production process, the ball grinding machine may be called cement mill, limestone ball mill, sand mill, coal mill, pebble mill, rotary ball mill, wet grinding mill, etc. JXSC ball mills are designed for high capacity long service, good quality match Metso ball mill. Grinding media Grinding balls for mining usually adopt wet grinding ball mills, mostly manganese, steel, lead balls. Ceramic balls for ball mill often seen in the laboratory. Types of ball mill: wet grinding ball mill, dry grinding ball mill, horizontal ball mill, vibration mill, large ball mill, coal mill, stone mill grinder, tumbling ball mill, etc. The ball mill barrel is filled with powder and milling media, the powder can reduce the balls falling impact, but if the power too much that may cause balls to stick to the container side. Along with the rotational force, the crushing action mill the power, so, it is essential to ensure that there is enough space for media to tumble effectively. How does ball mill work The material fed into the drum through the hopper, motor drive cylinder rotates, causing grinding balls rises and falls follow the drum rotation direction, the grinding media be lifted to a certain height and then fall back into the cylinder and onto the material to be ground. The rotation speed is a key point related to the ball mill efficiency, rotation speed too great or too small, neither bring good grinding result. Based on experience, the rotat
ion is usually set between 4-20/minute, if the speed too great, may create centrifuge force thus the grinding balls stay with the mill perimeter and dont fall. In summary, it depends on the mill diameter, the larger the diameter, the slower the rotation (the suitable rotation speed adjusted before delivery). What is critical speed of ball mill? The critical speed of the ball mill is the speed at which the centrifugal force is equal to the gravity on the inner surface of the mill so that no ball falls from its position onto the mill shell. Ball mill machines usually operates at 65-75% of critical speed. What is the ball mill price? There are many factors affects the ball mill cost, for quicker quotations, kindly let me know the following basic information. (1) Application, what is the grinding material? (2) required capacity, feeding and discharge size (3) dry or wet grinding (4) single machine or complete processing plant, etc.
Discrete element method (DEM) modelling has been used to systematically study the effects of changes in mill operating parameters and particle properties on the charge shape and power draw of a 5-m ball mill. Specifically, changes in charge fill level, lifter shape (either by design or wear) and lifter pattern are analysed. The effects of changes to the properties of the charge (ball fraction, ball and rock shape, type of ball and rock size distributions and the lower cutoff of the rock size distribution) can all be interpreted in terms of their effects on the shear strength of the charge. Some changes increase the shear strength leading to higher dynamic angles of repose of the charge, higher shoulder positions and higher power consumption for sub-critical speeds. For super-critical speeds, they lead to lower power consumption, due to lower particle mobility as the particles lock together better. Changes to the charge that weaken the interlocking of particles have the opposite effect on the charge shape and power consumption. The combination of these effects means that the speed for which peak power consumption occurs is predominantly determined by the shear strength of the charge material and the fill level. This demonstrates the sensitivity of mill behaviour to the charge characteristics and the critical importance of various assumptions used in DEM modelling.