construction of gyratory and jaw crusher

compare gyratory crusher vs jaw crusher

To accomplish this reduction in size takes several steps or stages of crushing and grinding. Primary crushing is the first of these stages. Generally speaking there are two types of primary crushers, lets compare them: GYRATORY CRUSHER or a JAW CRUSHER. Although they dont look anything like they do have similarities that put them into the same class of crusher.

Their CRUSHING SPEEDS are the same, 100 to 200 revolutions per minute. They both break the ore by COMPRESSION. That is they both break the rock by squeezing it until it breaks. On the average their final product will measure about seven inches at its widest point. And finally they both can be built to accept a rock up to sixty inches across.

Even if they are much alike, each of the two types of crushers has its own uniqueness. Because of this difference each type of crusher has its own environment that it operates best or at least better in, than the other.As an example, a gyratory crusher can be fed from two sides and handle ore that tends to slab. Also its design allows a higher speed motor with a high reduction ratio between the motor and the crushing surface. This is an important consideration as it means money saved in energy costs. A jaw crusher on the other hand requires a flywheel to store energy but can be used on the tougher ores due to its box frame construction. To be effective it must be fed from one side only but it handles square block-like ore well.

There is another comparison that should be taken into consideration, that is the amount of space that each takes. The Jaw crusher is the smaller of the two and its single feed point will make it a logical choice for underground workings. In the actual operation of the crushers, they both have similarities as well as differences so lets take each one separately and discuss its design and its problems. Considering the title of this chapter is Primary Crushing (Gyratory) we should discuss that one first.

In the introduction I mentioned that the purpose of a concentrator was to produce a concentrate of which ever mineral was being mined. To be able to recover this mineral it is necessary to reduce the ore in size until the mineral is LIBERATED. This means that the ore must be reduced in size until it is fine enough to be able to separate the mineral from the unwanted rock. In the Vocabulary of the metallurgist, at this point of the operation the unwanted rock will be termed the GANGUE material. You will notice that the terminology used for the ore will change depending upon the stage of concentration. The reason for this is to keep technical communication accurate.

jaw crusher vs gyratory crusher - jxscmachine

Jaw crusher and gyratory crusher as the primary crusher, play an important role in the crushing process. How to choose the suited primary crusher from the jaw crusher? Whats the difference between a jaw crusher and a gyratory crusher? JXSC starts with the following points: structure, capacity, energy consumption, maintenance.

All in all, if one set jaw crusher can achieve the needs of production, buy jaw crusher; if need two sets of jaw crusher, that would be better to buy a gyratory crusher. You may interest in 1. Single Toggle vs Double Toggle Jaw Crusher 2. Jaw Crusher Operation

construction of gyratory crusher

Simpler operation and maintenance. Construction of gyratory crusher: HGT gyratory crusher is a very large-scale equipment. In the design, it pays special attention to the convenience of maintenance. It is equipped with automatic lubrication and hydraulic system. The lubricating system can automatically lubricate heating, cooling and circulation according to the production conditions; it is equipped with an automatic spindle position control system, which can control the spindle through the hydraulic system, which facilitates the adjustment of the size of the ore discharge port, can also compensate the lining wear and control the product granularity; The gear adjusting device can conveniently adjust the backlash of the gear. The beam bushing and seal can be replaced without removing the beam. When the cross beam needs to be removed, a hydraulic cross beam separator can be configured.

Gyratory crusher combines mechanical, hydraulic, electrical, automation, intelligent control and other technologies into one. It benchmarks international advanced rotary crusher technology and is a new type of coarse crushing equipment with large capacity, high efficiency and intelligence. Compared with the traditional rotary crusher, the HGT gyratory crusher has higher crushing efficiency, low use cost, convenient maintenance and adjustment, and can provide users with efficient and intelligent ultra-large capacity coarse crushing solutions.

The crushing cone is mounted on the main shaft. The upper end of the main shaft is suspended on the beam by a conical nut, a conical compression sleeve, a bushing and a support ring. To prevent the cone nut from loosening, wedge keys are also installed on it. The tapered end of the bushing is supported on the support ring, while its side is supported on the bushing whose inner surface is tapered. When the crusher is running, the lower end of the bushing and the inner surface of the tapered bushing are conical surfaces. Therefore, the bush can be guaranteed to roll along the support ring and the conical sleeve, thereby meeting the requirements of the swinging movement of the crushing cone. The lower end of the main shaft is inserted into the eccentric hole of the eccentric shaft sleeve, which hole is eccentric to the axis of the crusher. When the eccentric shaft sleeve rotates, the axis of the crushing cone uses the fixed suspension point on the beam as the top of the cone to make a conical surface movement, thereby generating a crushing effect.

Gyratory crusher is one of the more widely used crushing equipment. The maintenance and repair of gyratory crusher is also a concern for users. Regular maintenance can detect problems in advance, prevent problems before they occur, and help extend its service life.

gyratory crusher - an overview | sciencedirect topics

Gyratory crushers were invented by Charles Brown in 1877 and developed by Gates around 1881 and were referred to as a Gates crusher [1]. The smaller form is described as a cone crusher. The larger crushers are normally known as primary crushers as they are designed to receive run-on-mine (ROM) rocks directly from the mines. The gyratory crushers crush to reduce the size by a maximum of about one-tenth its size. Usually, metallurgical operations require greater size reduction; hence, the products from the primary crushers are conveyed to secondary or cone crushers where further reduction in size takes place. Here, the maximum reduction ratio is about 8:1. In some cases, installation of a tertiary crusher is required where the maximum reduction is about 10:1. The secondary crushers are also designed on the principle of gyratory crushing, but the construction details vary.

Similar to jaw crushers, the mechanism of size reduction in gyratory crushers is primarily by the compressive action of two pieces of steel against the rock. As the distance between the two plates decreases continuous size reduction takes place. Gyratory crushers tolerate a variety of shapes of feed particles, including slabby rock, which are not readily accepted in jaw crushers because of the shape of the feed opening.

The gyratory crusher shown in Figure 2.6 employs a crushing head, in the form of a truncated cone, mounted on a shaft, the upper end of which is held in a flexible bearing, whilst the lower end is driven eccentrically so as to describe a circle. The crushing action takes place round the whole of the cone and, since the maximum movement is at the bottom, the characteristics of the machine are similar to those of the Stag crusher. As the crusher is continuous in action, the fluctuations in the stresses are smaller than in jaw crushers and the power consumption is lower. This unit has a large capacity per unit area of grinding surface, particularly if it is used to produce a small size reduction. It does not, however, take such a large size of feed as a jaw crusher, although it gives a rather finer and more uniform product. Because the capital cost is high, the crusher is suitable only where large quantities of material are to be handled.

However, the gyratory crusher is sensitive to jamming if it is fed with a sticky or moist product loaded with fines. This inconvenience is less sensitive with a single-effect jaw crusher because mutual sliding of grinding surfaces promotes the release of a product that adheres to surfaces.

The profile of active surfaces could be curved and studied as a function of the product in a way to allow for work performed at a constant volume and, as a result, a higher reduction ratio that could reach 20. Inversely, at a given reduction ratio, effective streamlining could increase the capacity by 30%.

Maintenance of the wear components in both gyratory and cone crushers is one of the major operating costs. Wear monitoring is possible using a Faro Arm (Figure 6.10), which is a portable coordinate measurement machine. Ultrasonic profiling is also used. A more advanced system using a laser scanner tool to profile the mantle and concave produces a 3D image of the crushing chamber (Erikson, 2014). Some of the benefits of the liner profiling systems include: improved prediction of mantle and concave liner replacement; identifying asymmetric and high wear areas; measurement of open and closed side settings; and quantifying wear life with competing liner alloys.

Crushers are widely used as a primary stage to produce the particulate product finer than about 50100mm. They are classified as jaw, gyratory, and cone crushers based on compression, cutter mill based on shear, and hammer crusher based on impact.

A jaw crusher consists essentially of two crushing plates, inclined to each other forming a horizontal opening by their lower borders. Material is crushed between a fixed and a movable plate by reciprocating pressure until the crushed product becomes small enough to pass through the gap between the crushing plates. Jaw crushers find a wide application for brittle materials. For example, they are used for comminution of porous copper cake. A Fritsch jaw crusher with maximal feed size 95mm, final fineness (depends on gap setting) 0.315mm, and maximal continuous throughput 250Kg/h is shown in Fig. 2.8.

A gyratory crusher includes a solid cone set on a revolving shaft and placed within a hollow body, which has conical or vertical sloping sides. Material is crushed when the crushing surfaces approach each other and the crushed products fall through the discharging opening.

Hammer crushers are used either as a one-step primary crusher or as a secondary crusher for products from a primary crusher. They are widely used for crushing hard metal scrap for different hard metal recycling processes. Pivoted hammers are pendulous, mounted on the horizontal axes symmetrically located along the perimeter of a rotor. Crushing takes place by the impact of material pieces with the high speed moving hammers and by contact with breaker plates. A cylindrical grating or screen is placed beneath the rotor. Materials are reduced to a size small enough to pass through the openings of the grating or screen. The size of the product can be regulated by changing the spacing of the grate bars or the opening of the screen.

The feature of the hammer crushers is the appearance of elevated pressure of air in the discharging unit of the crusher and underpressure in the zone around the shaft close to the inside surface of the body side walls. Thus, the hammer crushers also act as high-pressure, forced-draught fans. This may lead to environmental pollution and product losses in fine powder fractions. A design for a hammer crusher (Fig. 2.9) essentially allows a decrease of the elevated pressure of air in the crusher discharging unit [5]. The A-zone beneath the screen is communicated through the hollow ribs and openings in the body side walls with the B-zone around the shaft close to the inside surface of body side walls. As a result, the circulation of suspended matter in the gas between A and B zones is established and the high pressure of air in the discharging unit of crusher is reduced.

Crushers are widely used as a primary stage to produce the particulate product finer than about 50100 mm in size. They are classified as jaw, gyratory and cone crushers based on compression, cutter mill based on shear and hammer crusher based on impact.

A jaw crusher consists essentially of two crushing plates, inclined to each other forming a horizontal opening by their lower borders. Material is crushed between a fixed and a movable plate by reciprocating pressure until the crushed product becomes small enough to pass through the gap between the crushing plates. Jaw crushers find a wide application for brittle materials. For example, they are used for comminution of porous copper cake.

A gyratory crusher includes a solid cone set on a revolving shaft and placed within a hollow body, which has conical or vertical sloping sides. Material is crushed when the crushing surfaces approach each other and the crushed products fall through the discharging opening.

Hammer crushers are used either as a one-step primary crusher or as a secondary crusher for products from a primary crusher. They are widely used for crushing of hard metal scrap for different hard metal recycling processes.

Pivoted hammers are pendulous, mounted on the horizontal axes symmetrically located along the perimeter of a rotor and crushing takes place by the impact of material pieces with the high speed moving hammers and by contact with breaker plates. A cylindrical grating or screen is placed beneath the rotor. Materials are reduced to a size small enough pass through the openings of the grating or screen. The size of product can be regulated by changing the spacing of the grate bars or the opening of the screen.

The feature of the hammer crushers is the appearance of elevated pressure of air in the discharging unit of the crusher and underpressure in the zone around of the shaft close to the inside surface of the body side walls. Thus, the hammer crushers also act as high-pressure forced-draught fans. This may lead to environmental pollution and product losses in fine powder fractions.

A design for a hammer crusher (Figure 2.6) allows essentially a decrease of the elevated pressure of air in the crusher discharging unit [5]. The A-zone beneath the screen is communicated through the hollow ribs and openings in the body side walls with the B-zone around the shaft close to the inside surface of body side walls. As a result, circulation of suspended matter in the gas between A- and B-zones is established and high pressure of air in the discharging unit of crusher is reduced.

Jaw crushers are mainly used as primary crushers to produce material that can be transported by belt conveyors to the next crushing stages. The crushing process takes place between a fixed jaw and a moving jaw. The moving jaw dies are mounted on a pitman that has a reciprocating motion. The jaw dies must be replaced regularly due to wear. Figure 8.1 shows two basic types of jaw crushers: single toggle and double toggle. In the single toggle jaw crusher, an eccentric shaft is installed on the top of the crusher. Shaft rotation causes, along with the toggle plate, a compressive action of the moving jaw. A double toggle crusher has, basically, two shafts and two toggle plates. The first shaft is a pivoting shaft on the top of the crusher, while the other is an eccentric shaft that drives both toggle plates. The moving jaw has a pure reciprocating motion toward the fixed jaw. The crushing force is doubled compared to single toggle crushers and it can crush very hard ores. The jaw crusher is reliable and robust and therefore quite popular in primary crushing plants. The capacity of jaw crushers is limited, so they are typically used for small or medium projects up to approximately 1600t/h. Vibrating screens are often placed ahead of the jaw crushers to remove undersize material, or scalp the feed, and thereby increase the capacity of the primary crushing operation.

Both cone and gyratory crushers, as shown in Figure 8.2, have an oscillating shaft. The material is crushed in a crushing cavity, between an external fixed element (bowl liner) and an internal moving element (mantle) mounted on the oscillating shaft assembly. An eccentric shaft rotated by a gear and pinion produces the oscillating movement of the main shaft. The eccentricity causes the cone head to oscillate between the open side setting (o.s.s.) and closed side setting (c.s.s.). In addition to c.s.s., eccentricity is one of the major factors that determine the capacity of gyratory and cone crushers. The fragmentation of the material results from the continuous compression that takes place between the mantle and bowl liners. An additional crushing effect occurs between the compressed particles, resulting in less wear of the liners. This is also called interparticle crushing. The gyratory crushers are equipped with a hydraulic setting adjustment system, which adjusts c.s.s. and thus affects product size distribution. Depending on cone type, the c.s.s. setting can be adjusted in two ways. The first way is by rotating the bowl against the threads so that the vertical position of the outer wear part (concave) is changed. One advantage of this adjustment type is that the liners wear more evenly. Another principle of setting adjustment is by lifting/lowering the main shaft. An advantage of this is that adjustment can be done continuously under load. To optimize operating costs and improve the product shape, as a rule of thumb, it is recommended that cones always be choke-fed, meaning that the cavity should be as full of rock material as possible. This can be easily achieved by using a stockpile or a silo to regulate the inevitable fluctuation of feed material flow. Level monitoring devices that detect the maximum and minimum levels of the material are used to start and stop the feed of material to the crusher as needed.

Primary gyratory crushers are used in the primary crushing stage. Compared to the cone type crusher, a gyratory crusher has a crushing chamber designed to accept feed material of a relatively large size in relation to the mantle diameter. The primary gyratory crusher offers high capacity thanks to its generously dimensioned circular discharge opening (which provides a much larger area than that of the jaw crusher) and the continuous operation principle (while the reciprocating motion of the jaw crusher produces a batch crushing action). The gyratory crusher has capacities starting from 1200 to above 5000t/h. To have a feed opening corresponding to that of a jaw crusher, the primary gyratory crusher must be much taller and heavier. Therefore, primary gyratories require quite a massive foundation.

The cone crusher is a modified gyratory crusher. The essential difference is that the shorter spindle of the cone crusher is not suspended, as in the gyratory, but is supported in a curved, universal bearing below the gyratory head or cone (Figure 8.2). Power is transmitted from the source to the countershaft to a V-belt or direct drive. The countershaft has a bevel pinion pressed and keyed to it and drives the gear on the eccentric assembly. The eccentric assembly has a tapered, offset bore and provides the means whereby the head and main shaft follow an eccentric path during each cycle of rotation. Cone crushers are used for intermediate and fine crushing after primary crushing. The key factor for the performance of a cone type secondary crusher is the profile of the crushing chamber or cavity. Therefore, there is normally a range of standard cavities available for each crusher, to allow selection of the appropriate cavity for the feed material in question.

Depending on the size of the debris, it may either be ready to enter the recycling process or need to be broken down to obtain a product with workable particle sizes, in which case hydraulic breakers mounted on tracked or wheeled excavators are used. In either case, manual sorting of large pieces of steel, wood, plastics and paper may be required, to minimise the degree of contamination of the final product.

The three types of crushers most commonly used for crushing CDW materials are the jaw crusher, the impact crusher and the gyratory crusher (Figure 4.4). A jaw crusher consists of two plates, with one oscillating back and forth against the other at a fixed angle (Figure 4.4(a)) and it is the most widely used in primary crushing stages (Behera etal., 2014). The jaw crusher can withstand large and hard-to-break pieces of reinforced concrete, which would probably cause the other crushing machines to break down. Therefore, the material is initially reduced in jaw crushers before going through any other crushing operation. The particle size reduction depends on the maximum and minimum size of the gap at the plates (Hansen, 2004).

An impact crusher breaks the CDW materials by striking them with a high-speed rotating impact, which imparts a shearing force on the debris (Figure 4.4(b)). Upon reaching the rotor, the debris is caught by steel teeth or hard blades attached to the rotor. These hurl the materials against the breaker plate, smashing them into smaller particle sizes. Impact crushers provide better grain-size distribution of RA for road construction purposes, and they are less sensitive to material that cannot be crushed, such as steel reinforcement.

Generally, jaw and impact crushers exhibit a large reduction factor, defined as the ratio of the particle size of the input to that of the output material. A jaw crusher crushes only a small proportion of the original aggregate particles but an impact crusher crushes mortar and aggregate particles alike and thus generates a higher amount of fine material (OMahony, 1990).

Gyratory crushers work on the same principle as cone crushers (Figure 4.4(c)). These have a gyratory motion driven by an eccentric wheel. These machines will not accept materials with a large particle size and therefore only jaw or impact crushers should be considered as primary crushers. Gyratory and cone crushers are likely to become jammed by fragments that are too large or too heavy. It is recommended that wood and steel be removed as much as possible before dumping CDW into these crushers. Gyratory and cone crushers have advantages such as relatively low energy consumption, a reasonable amount of control over the particle size of the material and production of low amounts of fine particles (Hansen, 2004).

For better control of the aggregate particle size distribution, it is recommended that the CDW should be processed in at least two crushing stages. First, the demolition methodologies used on-site should be able to reduce individual pieces of debris to a size that the primary crusher in the recycling plant can take. This size depends on the opening feed of the primary crusher, which is normally bigger for large stationary plants than for mobile plants. Therefore, the recycling of CDW materials requires careful planning and communication between all parties involved.

A large proportion of the product from the primary crusher can result in small granules with a particle size distribution that may not satisfy the requirements laid down by the customer after having gone through the other crushing stages. Therefore, it should be possible to adjust the opening feed size of the primary crusher, implying that the secondary crusher should have a relatively large capacity. This will allow maximisation of coarse RA production (e.g., the feed size of the primary crusher should be set to reduce material to the largest size that will fit the secondary crusher).

The choice of using multiple crushing stages mainly depends on the desired quality of the final product and the ratio of the amounts of coarse and fine fractions (Yanagi etal., 1998; Nagataki and Iida, 2001; Nagataki etal., 2004; Dosho etal., 1998; Gokce etal., 2011). When recycling concrete, a greater number of crushing processes produces a more spherical material with lower adhered mortar content (Pedro etal., 2015), thus providing a superior quality of material to work with (Lotfi etal., 2017). However, the use of several crushing stages has some negative consequences as well; in addition to costing more, the final product may contain a greater proportion of finer fractions, which may not always be a suitable material.

The first step of physical beneficiation is crushing and grinding the iron ore to its liberation size, the maximum size where individual particles of gangue are separated from the iron minerals. A flow sheet of a typical iron ore crushing and grinding circuit is shown in Figure 1.2.2 (based on Ref. [4]). This type of flow sheet is usually followed when the crude ore contains below 30% iron. The number of steps involved in crushing and grinding depends on various factors such as the hardness of the ore and the level of impurities present [5].

Jaw and gyratory crushers are used for initial size reduction to convert big rocks into small stones. This is generally followed by a cone crusher. A combination of rod mill and ball mills are then used if the ore must be ground below 325 mesh (45m). Instead of grinding the ore dry, slurry is used as feed for rod or ball mills, to avoid dusting. Oversize and undersize materials are separated using a screen; oversize material goes back for further grinding.

Typically, silica is the main gangue mineral that needs to be separated. Iron ore with high-silica content (more than about 2%) is not considered an acceptable feed for most DR processes. This is due to limitations not in the DR process itself, but the usual customer, an EAF steelmaking shop. EAFs are not designed to handle the large amounts of slag that result from using low-grade iron ores, which makes the BF a better choice in this situation. Besides silica, phosphorus, sulfur, and manganese are other impurities that are not desirable in the product and are removed from the crude ore, if economically and technically feasible.

Beneficiation of copper ores is done almost exclusively by selective froth flotation. Flotation entails first attaching fine copper mineral particles to bubbles rising through an orewater pulp and, second, collecting the copper minerals at the top of the pulp as a briefly stable mineralwaterair froth. Noncopper minerals do not attach to the rising bubbles; they are discarded as tailings. The selectivity of the process is controlled by chemical reagents added to the pulp. The process is continuous and it is done on a large scale103 to 105 tonnes of ore feed per day.

Beneficiation is begun with crushing and wet-grinding the ore to typically 10100m. This ensures that the copper mineral grains are for the most part liberated from the worthless minerals. This comminution is carried out with gyratory crushers and rotary grinding mills. The grinding is usually done with hard ore pieces or hard steel balls, sometimes both. The product of crushing and grinding is a waterparticle pulp, comprising 35% solids.

Flotation is done immediately after grindingin fact, some flotation reagents are added to the grinding mills to ensure good mixing and a lengthy conditioning period. The flotation is done in large (10100m3) cells whose principal functions are to provide: clouds of air bubbles to which the copper minerals of the pulp attach; a means of overflowing the resulting bubblecopper mineral froth; and a means of underflowing the unfloated material into the next cell or to the waste tailings area.

Selective attachment of the copper minerals to the rising air bubbles is obtained by coating the particles with a monolayer of collector molecules. These molecules usually have a sulfur atom at one end and a hydrophobic hydrocarbon tail at the other (e.g., potassium amyl xanthate). Other important reagents are: (i) frothers (usually long-chain alcohols) which give a strong but temporary froth; and (ii) depressants (e.g., CaO, NaCN), which prevent noncopper minerals from floating.