double roll crusher catalogue

double roll crushers | mclanahan

Double Roll Crushers typically follow a primary or secondary crusher and are used for secondary and tertiary reduction of various minerals, such as ROM coal, clean coal, limestone, gypsum, trona, shale, bauxite, oil shale, coke, salt, lime, glass, kaolin, brick, shale and wet, sticky feeds. They are one of the most widely used crushers in the mining industry and have numerous advantages, such as high capacity, low headroom, low horsepower, the ability to handle wet, sticky feeds and the ability to produce a cubical product with minimum fines generation. Roll diameters and widths are dictated by the feed size, product size and capacity. The rule of thumb for the Double Roll Crushers ratio of reduction is 4:1.

The simplified design gives these units excellent reliability and requires very little maintenance. The crushers are designed with built-in tramp relief that allows for the passing of uncrushable objects while remaining in continuous operation and returning to the initial product setting. With a variety of roll surface designs, this crusher is capable of producing a much finer product. Since each machine is custom engineered, roll elements and tooth patterns are selected depending on each unique application.

McLanahan Double Roll Crushers feature slower roll speeds and a larger surface area to add prolonged life to the crushing elements, resulting in less maintenance downtime and decreasing your cost per ton. Double Roll Crushers generate minimum fines while producing a cubical product.

McLanahan Double Roll Crushers are designed for safety and many years of rugged operation. Effective tramp protection against non-crushable material is provided by an automatic spring-and-toggle system. This allows a movable roll to open, pass the material and return to its original setting for continued operation. Hydraulic product size adjustment allows producers to adjust for changes in product size requirements or to compensate for roll wear.

Operating Double Roll Crushers is quite simple. Whether it is a single or dual drive arrangement, the rolls are powered by electric motors and V-belt drive configurations, resulting in reliable and quiet operation. If it is a single drive arrangement, power is transferred from the driven roll to the non-driven opposing roll by an interstage V-belt drive. If it is a dual drive configuration, each roll is powered independently through a motor and V-belt drive.

During normal operation, the material is fed between the crushing rolls. A combination of compression and shear forces created between the opposing rolls reduce the feed material to the desired product size while producing a cubicle product with minimum fines.

McLanahans mechanical tramp relief systems employ a spring-and-toggle mechanism that activates whenever an uncrushable object enters the crushing chamber. Once an excessive force is applied to the movable roll, the toggles break open to allow the uncrushable item to pass. The high torsion springs then close the toggles, returning the movable roll to the previous setting. The crusher continues to operate uninterrupted.

When an uncrushable object, such as metal, roof bolts/timbers, etc., enters the crusher and the force necessary to crush this material is greater than the crushing forces of the crusher, the crusher allows the moveable roll to open and pass the tramp material and then return to its previous setting and remain in operation.

Depending on the customers desired product size and fines consideration, Mineral Sizers or Hammermills could be considered. The reasons people would consider a Roll Crusher over these alternative technologies include lower power requirements, less fines generation and costs.

Black Diamond Double Roll Crushers are the most versatile and popular model of McLanahan Double Roll Crushers. Ideal for secondary and tertiary crushing applications where product requirements drop down to (6mm), Black Diamond Double Roll Crushers are most commonly used to crush clean coal or friable materials with little or no hard refuse. They are available with single or dual V-belt drive.

Heavy-Duty Double Roll Crushers are ideal for the primary, secondary and tertiary crushing of limestone, gypsum, ROM coal, etc. where higher compressive strength material is anticipated. Due to the V-belt drive design, a lower horsepower is required compared to other crushers designed for the same applications.

Shalemaster Double Roll Crushers are driven mechanically with V-belt drives and gear reducers. They offer the same durability as other McLanahan Double Roll Crushers but are designed to handle wet, sticky feeds such as soft shale, kaolin and clay. The Shalemasters special tooth design and differential roll speeds provide optimum performance against plugging and other problems often associated with handling sticky materials.

Typically used as secondary or tertiary crushers, McLanahan Double Roll Crushers provide a 4:1 reduction ratio and can be used following other McLanahan equipment, such as Feeder-Breakers, Rotary Breakers, primary DDC-Sizers, or Single Roll Crushers, when further reduction of primary crushed material is required. Each Double Roll Crusher is selected and engineered for its specific application, thus roll elements and tooth patterns are selected based on the customers unique applications and designed to produce a cubical product with minimal fines.

double roll crusher brochure | mclanahan

Typically used as secondary or tertiary crushers, McLanahan Double Roll Crushers provide a 4:1 reduction ratio and can be used following other McLanahan equipment, such as Feeder-Breakers, Rotary Breakers, primary DDC-Sizers, or Single Roll Crushers, when further reduction of primary crushed material is required. Each Double Roll Crusher is selected and engineered for its specific application, thus roll elements and tooth patterns are selected based on the customers unique applications and designed to produce a cubical product with minimal fines.

double roll & teethed roll crusher

Although its brief period of popularity passed some thirty-odd years since, and only a few sets were installed before interest reverted to other types, the high-speed double roll crusher developed by Thomas A. Edison shortly before the end of the last century warrants a place in any discussion-of crushing equipment. In 1960, the largest machine of this type the 6 x 7 foot giant rolls were huge crushers, judged even by present-day standards; they have an unobstructed receiving opening 7 x 7 foot and their capacity on individual skip-loads of stone is enormous, although, as will be explained, they cannot maintain this peak capacity over a period of time.

Mechanically, the teethed roll crusher is a very simple machine. The two rolls are carried in bearings, supported on two very heavy and rigid bed castings which are secured on the concrete foundation by a number of large anchor bolts. The bearings, in addition to being bolted to these bed castings, are prevented from spreading by pairs of large tie-rods which pass through them above and below the roll shafts. Unlike the smooth-face crushing rolls we have described, these tension rods are not cushioned by springs. The machine is surmounted by a heavy cast rectangular hopper, all sides of which are vertical. Each roll is independently driven by a flat-belt pulley.

The roll-centres are octagonal in cross section, each face being provided with a spline groove and a series of tapped holes for securing the chilled- iron wearing plates. These wearing plates have the sledging knobs, or teeth, cast on their outer surfaces. Thus we have a roll surface that resembles that of the one rollcrusher, except that the faces of all teeth are sloped instead of radial on the advance side. The usual practice is to fit one roll entirely with so-called regular teeth, and the other roll with six rows of regulars and two rows of higher (slugger) teeth.

The peripheral speed, or tip-velocity, of these rolls is much higher than that of any of the machines we have previously described. The range of the smooth-face rolls, for example, is from about 400 ft/min for the small 12-in. rolls, to 2000-2200 feet/minute for the heavy-duty 72 machine. The single-roll crusher has a tip speed of 400-450 ft/min while the 6- x 7-ft teethed roll crusherhas a normal, no-load, surfaces speed of just under 3500 ft/min. It can be readily appreciated that this high velocity induces an extremely violent crushing action, in conjunction with the 3- to 4-in. knobs which protrude from the roll surfaces. Impact, sledging, and pressure crushing enter into the over-all performance; but impact, in this crusher, plays a far more important role than it does in the slower speed single-roll machine; and crushing, even well down along the roll faces, is more in the nature of a sledging action than it is of pressure crushing, for this action occurs in the lower-velocity crushers.

The theoretical maximum size of cube that the knobs will grip, when the rolls are set at minimum spacing, is 24; but the rolls will reduce any stone that can be introduced into the 7-ft square hopper. Large blocks will span across the tops of the two rolls; immediately the slugger teeth on the one roll so equipped go to work on these blocks and quickly shatter them into pieces that can be gripped between the sets of regular teeth; from this point on, the action is a mixture of sledging and pressure crushing. The same selective segregations which we described in connection with the single-roll machine occur in the double-roll crusher; the smaller pieces are cleared quickly, leaving the roils free to work on the larger blocks.

The entire performance on individual skip-loads of stone takes place in a very short period of time. Ten- ton loads of mixed-size medium limestone will clear the crusher in from 10 to 15 sec.; large single blocks, weighing from 6 to 8 tons, are crushed in from 5 to 20 seconds, depending upon the toughness of the individual piece, and upon the way it happens to land in the crushing chamber. These performances were clocked on ma-chines turning out a 6 product.

The short-time transfer of energy, especially when crushing large blocks, is very high; so high in fact that it would not be economically feasible to provide sufficient motive power to deliver it. The usual practice, when these rolls are driven electrically, is to drive the slugger roll with a 250 HP motor, and the regular roll with 200HP,a total of 450 HP. As compared to this motive power, instantaneous energy delivery may run as high as 4000 HP, obviously far beyond the capacity of the motive equipment. But the rolls themselves, when running at normal no-load speed, have a stored kinetic energy of upwards of 4,000,000 ft -lb , and it is this stored energy that does much of the actual crushing, the motors serving to bring the rolls back to normal speed between crushing periods. In crushing a skip-load of stone the rolls may lose anywhere from 30 to 60 RPMin speed; this loss occurs partly through slowing down of the motive equipment, and partly through belt slippage. It requires from 5 to 10 sec. to bring the machine back to speed, during which time the power input will vary from 400 to 600 HP. The power required to run the rolls empty is something less than 100 hp. The average power consumption, when crushing from 3000 to 4000 tons per 10 hour day will run in the neighbourhood of 150 HP on medium limestone.

While the average power consumption of this machine compares favorably with that of other types, the rather violent fluctuation outlined and the relatively high connected horsepower are unfavourable features. It is also natural to expect that the belt slippage we have noted would constitute something of a problem over a period of time. Performance records indicate that belt trouble accounts for about 50% of the total lost time on a set of these rolls, and about 25% of the total maintenance expense.

The type of quarry equipment most commonly used in conjunction with this crusher is the three-sided steel skip, carried on a flat-top truck or flat car. These skips are provided with a shackle on the rear end, which is engaged by a hook actuated by a small hoist. This apparatus slides the skip over against the lip of the receiving hopper, and tilts it to discharge its contents. The skips discharge over a feed-roll which retards the flow of material so that the entire load does not drop into the crushing chamber at once. When the skip is empty it is pulled back on to the truck or car by a counterweight attached to the opposite end of the same cable which performs the hoisting operation.

We have mentioned the heavily ribbed hopper which surmounts the frame and extends up to the level of the feed roll. This hopper serves the double purpose of directing the material into the crushing zone, and preventing stones thrown by the slugger teeth from flying out of the crusher. It is also necessary to cover the top of the hopper with heavy netting to contain flying spalls.The straight-sided, rectangular hopper construction, and the violent agitation in the crushing chamber, tend to minimize blocking and bridging in this crusher. When bridges do occur they are difficult and dangerous to break while the rolls are running.

Practically all that we have had to say about the application of the single-roll crusher will apply as well to the Edison toothed roll crusher. It is better adapted to handling blocky stone than is the single-roll machine, because itsslugging action is much more vigorous, and it will handle any material that will not build up on the sides of the vertical hopper. It is not as simple a machine to feed as the single roll crusher, because its narrow hopper necessitates the uses of skips, or very short-bodied cars. A heavy- duty apron feeder would of course solve this problem, but so far as we know, none of these crushers were so equipped. The high peak capacity of the crusher constitutes something of a problem in plants of medium capacity. It is not economically feasible to provide elevating or conveying equipment to handle peak loads of around 4000 TPH in a plant designed to turn out that much stone in an 8 or 10 hr day; consequently means must be provided to smooth out these high surge loads. This can be taken care of by a surge bin and feeder below the crusher, or by passing the roll product direct to a secondary crusher of uniform-capacity characteristic. A feeder ahead of the rolls would smooth out peaks on mixed feed but. once a 10 or 12 ton block of stone is dropped into the crusher, that quantity comes through very quickly as crushed stone, which would render the regulating properties of the feeder of questionable value.Modified forms of this crusher were used by Edison for secondary and tertiary stages. The crushing equipment in one large plant, for example, comprised a set of 6- x 7-ft rolls (8 product), a set of 4 x 4 feet secondary rolls (3.5 product), and a set of 4 x 3 ft tertiary rolls (1.5 product), these last rolls being in closed circuit. These smaller machines were also run at high speeds, their surface velocities being slightly over 3000 ft/min.

double roll crusher, laboratory roll crusher, in naihati , east west corporation | id: 4782015412

We are one of the leading suppliers of different types of crushers that are used extensively in different industries such as metallurgy, mining, building material, energy etc. We manufacture in three main types of crushers that include single and double toothed roll crushers, smooth double roll crushers and sinter crusher.

Single toothed roll crusher comprises of rotary roller that includes large tooth and also a crushing plate that is adjustable. The material that needs to be crushed is first smashed and pressed in the single-tooth roll breaker. Through the top of the hopper of the single toothed roll crusher, the material is put into the breaking cavity and then the rotary roller places it between the crushing plate and the tooth roller for breaking.

Double toothed roll crushers are used extensively for the crushing of different kinds of rock and ore in different industrial sectors such as chemistry, cement, mining etc. Double toothed roll crushers comprise of rolls, housing, deep tooth gear, double motors, safety spring and double belts etc. Electric motors drive two counter rotating crushers through coupling and gearbox. The feed material is fed through a feeding device across the rolls of double toothed roll crusher.

Our smooth double roll crushers that are extensively used in industries where narrow spectrum is needed. Smooth double roll crushers contain components such as safety spring, deep tooth gear, housing and rolls.

Our specifically designed single roll crushers are also used as sinter crushers that perform the task of primary crushing in the iron and steel industry. Sinter crusher is usually equipped with a directly-driven crushing roll that has strong crushing teeth as well as a grizzly bar carrier and a mobile frame that streamlines maintenance.

At the outset, we take this opportunity to introduce ourselves as a growing organization engaged in Business Development, Management, Marketing, Project Co-ordination and all types of Techno-commercial activities, engineering & technical services required at different stage in following major fields.

We have also tied up with some leading Design Engineering, Manufacturing, Construction & Third party agencies/ Consultants for Engineering & Technical services / supports in horizontal synergy under the banner of EAST WEST CORPORATION.

We have enviable manpower strength equipped with hardcore professional engineers of various disciplines who have contributed their services very successfully in different field of Indian industry in organization like L&T, McNally Bharat Engineering Co. Ltd, TRF Ltd. M.N. Dastur & Co., Siemens etc. Having been experienced and expertise with proven track knowledge, our engineers, marketers / channel partners have been developed substantial volume of business in their similar line. Our ASSOCIATES / Third party AGENCIES are working as a counter part of some leading organizations in India and abroad in the field of Bulk material handling turnkey projects, Crushing & Screening Plants, Mining machinery, Power transmission products, Capital equipment, Industrial utilities and spares.

double roll crusher, 13mm particle size - gilson co

Double Roll Crushers are designed for single-pass size reduction of medium-hard to hard materials such as rock or ore to a nominal minus 10 mesh. Topsize is approximately 13mm and final fineness typically passes a No. 10 (2mm) opening, depending on material type. Roll Crushers work well in preparing samples for further fine reduction using a pulverizer. Output size is controlled by adjusting the gap between the rollers using a hand lever. Feed hoppers offer high capacity, open easily for cleaning and maintenance access, and feature an electrical safety interlock that shuts down power to the unit when the hopper is opened.

The crushers are rugged with easy-to-operate capabilities that meet the rigorous demands of laboratory and pilot plant operations. The Double Roll Crushers are mounted on a heavy steel base, include strong relief springs, and are fully-equipped with safety guards. These crushers are constructed of fabricated steel and equipped with a fabricated steel drive guide for operator safety. They have a tilt-design feed hopper, cast Ni-hard roll facings for long-life, relief springs, and heavy-duty pillow block bearings.

LC-13 Marcy Double Roll Crusher features 6.5x6in (165x153mm), Dia.xW heavy 304 stainless steel crushing rolls with Ni-hard roll facings. The 2hp TEFC motor with V-belt drive produces a uniform speed throughout the crushing process. This model is capable of reducing most rock-like materials of 0.5in (13mm) feed size to minus No. 10 (2mm) at a capacity up to 3,000lbs (1,361kg) per hour. Operates at 60Hz. Voltage of 230V or 460V must be selected at time of order.

LC-14 Marcy Double Roll Crusher features 9x12in (229x305mm), Dia.xW heavy 304 stainless steel crushing rolls with Ni-hard roll facings. The unit features a V-belt drive, with a 5hp TEFC motor that produces uniform speed throughout the crushing process. It can reduce most rock-like materials of 0.5in (13mm) feed size to minus No. 10 (2mm) at a capacity up to 8,000lbs (3,629kg) per hour. Operates at 60Hz. Select preferred voltage of 230V or 460V when ordering.