mobile ball mill gold ore machine in india

what are the differences between ball mill and rod mill? | fote machinery

Ball mill and rod mill are the common grinding equipment applied in the grinding process. They are similar in appearance and both of them are horizontal cylindrical structures. Their cylinders are equipped with grinding medium, feeder, gears, and transmission device.

The working principle of ball mill and rod mill machine is similar, too. That is, the cylinder drives the movement of the grinding medium (lifting the grinding medium to a certain height then dropping). Under the action of centrifugal force and friction, the material is impacted and ground to required size, so as to realize the operation of mineral grinding.

Grate discharge ball mill can discharge material through sieve plate, with the advantage of the low height of the discharge port which can make the material pass quickly so tha t to avoid over-grinding of material. Under the same condition, it has a higher capacity and can save more energy than other types of mills;

It is better to choose a grate discharge ball mill when the required discharge size is in the range of 0.2 to 0.3 mm. Grate discharge ball mill is usually applied in the first grinding system because it can discharge the qualified product immediately.

Overflow discharge ball mill can grind ores into the size under 0.2 mm, so it is very suitable for the second grinding system. The capacity of it is about 15% lower than grate discharge ball mill in the same specification, and the loaded grinding medium is also less than that one.

It can be divided into three types of rod mills according to the discharge methods, center and side discharge rod mill, end and side discharge rod mill and shaft neck overflow discharge rod mill.

It is fed through the shaft necks in the two ends of rod mill, and discharges ore pulp through the port in the center of the cylinder. Center and side discharge rod mill can grind ores coarsely because of its structure.

This kind of rod mill can be used for wet grinding and dry grinding. "A rod mill is recommended if we want to properly grind large grains, because the ball mill will not attack them as well as rod mills will."

It is fed through one end of the shaft neck, and with the help of several circular holes, the ore pulp is discharged to the next ring groove. The rod mill is mainly used for dry and wet grinding processes that require the production of medium-sized products.

The diameter of the shaft neck is larger than the diameter of the feeding port about 10 to 20 centimeters, so that the height difference can form a gradient for ore pulp flow. There is equipped with a spiral screen in the discharge shaft neck to remove the impurities.

It has high toughness, good manufacturability and low price. The surface layer of high manganese steel will harden rapidly under the action of great impact or contact. The harder index is five to seven times higher than other materials, and the wear resistance is greatly improved.

It has high toughness, good manufacturability and low price. The surface layer of high manganese steel will harden rapidly under the action of great impact or contact. The harder index is five to seven times higher than other materials, and the wear resistance is greatly improved.

It is made of several elements such as chromium and molybdenum, which has high hardness and good toughness. Under the same work condition, the service of this kind of ball is one time longer than the high manganese steel ball.

After the professional technology straightening and quenching processing process, a high carbon steel rod has high hardness, excellent performance, good wear resistance and outstanding quality.

The steel ball of ball mill and the mineral material are in point contact, so the finished product has a high degree of fineness, but it is also prone to over-grinding. Therefore, it is suitable for the production with high material fineness and is not suitable for the gravity beneficiation of metal ores.

The steel rod and the material are in line or surface contact, and most of the coarse particles are first crushed and then ground. Therefore, the finished product is uniform in quality, excellent in particle size, and high in qualification rate.

The cylinder shape of the rod mill and the ball mill is different: the cylinder of the rod mill is a long type, and the floor area is large. The ratio of the length to the diameter of the cylinder is generally 1.5 to 2.0;

The cylinder of the ball mill is a barrel or a cone. And the ratio of the length to the diameter of the cylinder is small, and in most cases the ratio is only slightly larger than 1, and the floor area is small, too.

The above is the main content of this article. The ball mill and the rod mill are the same type of machine on the appearance, but there are still great differences in the interior. It is very necessary to select a suitable machine for the production to optimize the product effect and maximize its efficiency.

As a leading mining machinery manufacturer and exporter in China, we are always here to provide you with high quality products and better services. Welcome to contact us through one of the following ways or visit our company and factories.

Based on the high quality and complete after-sales service, our products have been exported to more than 120 countries and regions. Fote Machinery has been the choice of more than 200,000 customers.

ball mills

Ball Mills What Are These Machines and How Do They Work? Short flash video at bottom of page showing batch ball mill grinding in lab. May have to click on browser "Allow Active X blocked content" to play A Ball Mill grinds material by rotating a cylinder with steel grinding balls, causing the balls to fall back into the cylinder and onto the material to be ground. The rotation is usually between 4 to 20 revolutions per minute, depending upon the diameter of the mill. The larger the diameter, the slower the rotation. If the peripheral speed of the mill is too great, it begins to act like a centrifuge and the balls do not fall back, but stay on the perimeter of the mill. The point where the mill becomes a centrifuge is called the "Critical Speed", and ball mills usually operate at 65% to 75% of the critical speed. Ball Mills are generally used to grind material 1/4 inch and finer, down to the particle size of 20 to 75 microns. To achieve a reasonable efficiency with ball mills, they must be operated in a closed system, with oversize material continuously being recirculated back into the mill to be reduced. Various classifiers, such as screens, spiral classifiers, cyclones and air classifiers are used for classifying the discharge from ball mills. This formula calculates the critical speed of any ball mill. Most ball mills operate most efficiently between 65% and 75% of their critical speed. Photo of a 10 Ft diameter by 32 Ft long ball mill in a Cement Plant. Photo of a series of ball mills in a Copper Plant, grinding the ore for flotation. Image of cut away ball mill, showing material flow through typical ball mill. Flash viedo of Jar Drive and Batch Ball Mill grinding ore for testing Return To Crushing Info Page Contact Us Copyright 1994-2012 Mine-Engineer.Com All Rights Reserved

gold milling process -primitive and basic

At the time, 1890, the Author said There is, of course, nothing for us to learn from this imperfect and rudimentary gold-extraction process described here, which is doubtless destined to disappear ere long, before the progress of scientific mining, now making itself slowly felt throughout the far East. I think it advisable, however, to put on record all such crude efforts, if only to enable us to trace more completely the evolution of our modern systems of mining, and to teach us by what widely-divergent methods different races of mankind have attempted to solve one, apparently simple, problem.

Their method of mining was then, and is now, the following: A small water-furrow is first brought in at the highest possible level on a suitable hill-side, and the stream is turned down the hill. By means of a heavy long wooden crowbar, shod with a long strongly- made chisel-pointed iron socket, and with the help of the stream of water, which rarely exceeds 50 cubic feet per minute, the surface- soil and weathered country-rock are loosened and sluiced away. No trouble is taken to save any of the gold washed down, except in one or two instances where rude riffles have been inserted in the tail-race; the race is, however, carefully searched for bits of quartz showing visible gold, which are picked out and put on one side. The surface of the shales is thus stripped, and any veins of gold that may be laid bare are then worked. The principal mining- tool is a rough kind of pick, and the use of explosives, or even of wedges, is quite unknown. Neither shovels nor barrows are used ; their places are taken by broad hoes and baskets, a pair of the latter, swung at each end of a stick and holding at least 70 pounds, being easily carried up steep grades by a Chinese miner. The tunnels, small and irregular, usually incline steeply upward ; they are rudely timbered, and as timber decays rapidly in this climate, these workings cannot penetrate far into the hills, but soon have to be abandoned, and the whole series of operations has to be recommenced.

A party of 27 miners, who owned and worked a rich hillside, considered themselves to be doing well when their entire days output (they do not work night-shifts as a rule) was a little over half a ton of quartz. The quartz, as extracted from the reef, is cobbed down with hammers to about pass a 1 J-inch ring, and is then carefully hand-picked, all stone showing visible gold, sulphurets or any other favorable indications being sent to the mill and the restbeing thrown away. From one-eighth to one-half is thus rejected. I have assayed many samples of this refuse rock, which carries from 3 to 10 pennyweights of free milling gold to the ton, so that it is quite worth milling according to our modern ideas.

At first the mode of crushing adopted by the Chinese consisted in heating the rock red-hot, quenching it in water and then pounding it down and rubbing it between two stomps. About 35 years ago atilt-hammer, made entirely without iron and having a stone head, was introduced, and is still much used by individual miners. About twelve years ago the battery of three to six hammers, worked by a water-wheel, was first employed. It is said to have been copied from mills for crushing the materials of joss-sticks. Tilt-hammer rice-mills are also built. Such water-mills are usually the property of a party of miners working together.

The foot-mill shown in Figs. 1 and 2 is of the usual type, from which there are but few unimportant departures. The entire falling weight is about 45 pounds, and the length of drop about 20 inches; as a rule, these mills are worked at 15 to 20 blows per minute.

The mill shown is built entirely without iron; the stone that forms the base of the mortar is a piece of hard quartzite or of barren reef-quartz, the same material being used for the hammer-head, which is firmly held in its socket by wooden wedges, the socket being kept from splitting by a stout hoop of rattan twisted round it. Some of the mills use iron hoops, and some have iron spindles for the hammer to work on; with these exceptions and one or two other very unimportant details, the construction is always the same, though the dimensions may vary a little. There is scarcely a house in the whole district that has not one of these mills.

The Chinese usually work these mills for about eight hours per day. A shovelful of quartz is first thrown into the mortar and the mill is then worked by the foot of the miner, who stands on one or other of the stones shown in the drawings, grasping the uprights or else a cross-bar that is sometimes fastened across them.

When the quartz is supposed to be crushed sufficiently fine, the hammer-head is propped up, and the crushed stone is scraped out and sifted through a circular sieve 15 inches to 20 inches in diameter, and about 1J inches deep. The sieve itself is made of thin strips of rattan about 0.1 inch in width. There are from 36 to 40 holes per square inch, so that the width of mesh varies between 0.04 and 0.06 inch. A man can crush in a working day, with one of these mills, from 70 lbs. to 140 lbs. of stone, according to its hardness.

The number of heads in a power-mill varies between 3 and 6, depending principally on the quantity of water available. As the district is well watered, the large majority are 6-stamp mills; out of 11 power-mills which it contains, 8 are 6-stamp mills. Figs. 3 and 4 show the usual type of the latter mills, from which pattern there is practically no departure. I could not even induce the Chinese to try a curved cam instead of a straight one, as they seemed to consider such innovations dangerous ; and they added that wood and water were both cheap enough. As will be noticed, the construction of the water-wheel is extremely crudethe water, which issometimes brought down very steep hills from considerable heights in small, highly-inclined ditches, strikes the flat buckets with considerable velocity, so that the wheel is partly an impact and partly a pressure wheel; the buckets are never more than half-filled at the best, and the wheel is sometimes allowed to wade in tail-water to the full depth of the shrouding. Much power is accordingly wasted, the amount of water consumed in driving one of these mills beingfrom 80 to 100 cubic feet per minute. The average number of drops of each head varies between 27 and 32 per minute; the length of the drop is about 2 feet, and the effective falling weight of the head is about 70 lbs. Thus only about one-third of the theoretical power of the water is utilized, but of course much of this loss of energy is due to the friction of the whole machine, notably between the straight cam and the tailpiece of the hammer. There are usually 3 men per shift working one of these mills, 2 being engaged in looking after and feeding the machine, while the third sifts thepounded stone as already described, throwing back under one of the hammer-heads whatever will not pass the sieve.

The cost of one of these mills complete, including a substantial shed over it thatched with palm leaves, but excluding the water- furrow, is said to be about very little, and they are supposed to last from 5 to 7 yearsneeding, however, constant repairs.

A stone hammer-head lasts from a week to a month, according to its quality. They are made, as in the foot-mills, from boulders of quartz rock, and it is mostly one mans business to search for these boulders in the bed of the stream, and, when found, to dress them into shape.

I tested the degree of fineness to which these mills reduce the quartz by differential siftings of a number of samples, taken by spoon-sampling the heaps of crushed ore lying at various mills. The results of some of my tests are given in the following table :

It appears from the above table that a great deal of the ore is crushed very fine (too fine, indeed), while some is not fine enough. As about 40 per cent, of the ore will pass through a 6,400 sieve, there must be much over-stamping, resulting, no doubt, in the production of a great deal of float-gold and slimes.

After the mill has been running for a longer or shorter period, according to circumstances, a clean-up takes place. The crushed ore is carried out in large wooden pails to a Chinaman, who washesit, squatting down by the side of a square pit, through which a small stream of clear water is kept running. The implement used for washing is a flat, somewhat conical wooden dish, cut from the spurs of certain hard-wood trees, and fashioned with much care. It is known as the dulang, and much resembles the Spanish-American batea, except that the section of the former is that of a very obtuse rounded cone, while the section of the latter is approximately that of a sphere.

A section of a typical dulang is shown in Fig. 5. Much importance is attached to the correct shape of the conical point, as it is in this that the precious metal is gathered together. The dulang is filled with from 10 to 15 lbs. of crushed stone, according to its size, and this is washed by a curious circular, combined with a slight undulatory motion, by which the particles of light, barren quartz are swept over the edge of the dulang, which is held just dipping below the surface of the water in the pit, while the heavier particles are collected in the rounded apex of the cone. When nearly cleaned, the gold and concentrates are transferred to a smaller, very carefully made and polished dulang, about 1 foot in diameter, in which thequartz is washed off as thoroughly as possible, and the gold, by a skillful jerk, is thrown clear from the sulphurets, and finally collected in a small brass dish. The sulphurets still retain much coarse gold, to which they cling obstinately. They are ground as fine as possible on a stone and re-washed several times, a good deal of the gold being thus separated and added to that previously obtained. Even then the sulphurets still carry much gold, the larger portion of which is free. They are stored away in jars while wet and allowed to rust, and after a time they are sometimes re-crushed and re-washed ; very often, however, they are merely allowed to accumulate and are not treated further. The first tailings are re-washed, and then stacked.

The cleaned gold is dried and melted over a small forge provided with a box-shaped wooden blower of the usual Chinese type. The fuel is charcoal. Tiny, conical crucibles, capable of holding about a couple of ounces of gold are used; the gold-dust is melted in these with borax and niter as fluxes; the slag is lifted off the surface of the gold when the latter is supposed to be clean, by means of an iron rod, and the gold is then granulated by pouring into water. If it is not considered to be sufficiently soft and pure it is re-melted, and the process is repeated until the gold is quite soft. The principal impurities removed seem to be sulphur, arsenic, a little copper, and perhaps traces of lead. Both the granulated gold and the crude gold-dust, as also gold got from river-washing, are used as currency in this district, coined money being scarcely ever seen here, and then only in the form of the old dollar.

In a partial wash-up at one of these mills, during my stay in the district, the following results, considered to be exceptionally good, were obtained, the quantity washed being as nearly as possible 2000 pounds of crushed ore:

As a general rule, there seems to be left in the tailings about one- third of the gold originally present in the ore, while there must be a considerable additional loss of float-gold carried away in the process of washing, due to the original fineness of some of the gold in the ore, and to the over-stamping already referred to.

From the average of these two assays it would appear that nearly one-third of the original proportion of gold is still left in the tailings. I might quote numerous other assays, but the results in all cases were approximately the same; there were no really clean tailings at all, in spite of the fact that they were all the result of handling sur- face-ores, where practically the whole of the gold was free. The losses above indicated appear enormous, but it must be remembered that the thrifty Chinamen throw nothing awaynot even tailings; however completely, in their opinion, these may be exhausted, they still pile them up and keep them. When, for any reason, their mill would otherwise be idle, they re-pound and re-wash their old tailings, and always get some gold out of them. The piles of tailings are, however, left exposed, so that a considerable proportion gets washed down into the streams and rivers by the heavy rains that occur at each change of monsoon ; and there are a good many Chinese of the poorer classes who make a sort of living by washing the sands in the river-beds, the gold they get being principally, to all appearance, that which has been thrown into the rivers by the miners up stream. It is noticeable that there is no gold, or very little, to be found in the rivers above the points where there are mines in operation. A fair days work of one Chinaman in the river-bed (say six hours actual work) was found, as the average of several trials, to produce an output of 7.3 grains of gold about .940 fine, worth say little in localcurrency. This quantity of gold was obtained by washing 22 large dulangs of gravel, each holding about 70 pounds of dirt.From the average of these two assays it would appear that nearly one-third of the original proportion of gold is still left in the tailings. I might quote numerous other assays, but the results in all cases were approximately the same; there were no really clean tailings at all, in spite of the fact that they were all the result of handling surface-ores, where practically the whole of the gold was free. The losses above indicated appear enormous, but it must be remembered that the thrifty Chinamen throw nothing awaynot even tailings; however completely, in their opinion, these may be exhausted, they still pile them up and keep them. When, for any reason, their mill would otherwise be idle, they re-pound and re-wash their old tailings, and always get some gold out of them. The piles of tailings are, however, left exposed, so that a considerable proportion gets washed down into the streams and rivers by the heavy rains that occur at each change of monsoon ; and there are a good many Chinese of the poorer classes who make a sort of living by washing the sands in the river-beds, the gold they get being principally, to all appearance, that which has been thrown into the rivers by the miners up stream. It is noticeable that there is no gold, or very little, to be found in the rivers above the points where there are mines in operation. A fair days work of one Chinaman in the river-bed (say six hours actual work) was found, as the average of several trials, to produce an output of 7.3 grains of gold about .940 fine.

It is interesting to note that in custom-milling, of which there is a good deal done here (many of the fossickers sending all the gold quartz they collect, whether by mining or picking out of the river- gravels, to one of the water-mills for crushing), the charge made is equal to just a few $U. S. per (long) ton of quartz, this payment including the washing of the gold, but not, so far as I can make out, its cleaning and melting.

It is obvious from the above description, that the total quantity of stone crushed by all the mills in the district, supposing them all to be going simultaneously, and including the foot-mills, could not exceed some 12 tons a day at the best, an amount that could be far more economically and efficiently handled in a five-stamp Californian mill of moderate power. Yet the total annual output of gold from this district (including, however, alluvial as well as reef-gold) is said to be 4861 ounces, fully .900 fine. The total number of men engaged in mining, in one way or another, is close upon one thousand.