principle of roller mills

what is the tutorial principle of ultrafine roller mill equipment for heavy calcium?

New ultrafine roller mill is the mainstream equipment of grinding heavy calcium fine powder project. Due to high capacity and more energy-saving, it is favored by the industry. So, how does the superfine grinding machine of heavy calcium grind?

The production of this energy-saving ultra-fine ring roller mill equipment has the advantages of crushing performance such as rolling, grinding and impact. It mainly grinds talc, calcite, calcium carbonate, dolomite and so on. Its fineness can be adjusted between 325-2500 mesh, easy to operate, wide use, stable performance, high cost performance, small area, is a new choice for fine powder processing.

The utilization rate of coal mine energy is relatively high, because there are a lot of slag produced by coal industry smelting every year. In order to avoid these slag damage to the environment and increase the recycling utilization rate, slag grinding mill is a more thorough and effective way of utilization.

Source: guikuang By Administrator Posted: 2019-02-22 As we all know that the Raymond mill is one of the common use stone powder making machines, compare with other grinding mills, the Raymond mill usually is more stable and efficient. However, after a []

Source: GuikuangBy Administrator Posted: 2019-02-22 In the field of fluorite grinding, Raymond mill will be one of the most popular machines for fluorite powder grinding. As a common grinding mill for fluorite powder processing, fluorite Raymond mill is an excellent high efficiency equipment. It has scientific principles and design structure, high productivity, low energy consumption, []

Source: guikuang By Administrator Posted: 2019-02-25 As a common grinding plant, Raymond Mill can be used in fine powder making of barite, calcite, potassium feldspar, talc, marble, limestone, dolomite, fluorite, lime, activated clay, activated carbon, bentonite, kaolin, cement and phosphate rock, and other Non-flammable and []

Source: Guikuang By Administrator Posted: 2019-2-21 Generally speaking, the price of Raymond mill usually more cheaper than other grinding mills, and compare with other grinding mills, the Raymond mill usually has a stable performance, the capacity of Raymond mill can up to 20 t/h, and []

roller mill: components, designs, uses, advantages and disavan

Roller mill is a form of compression mill that uses a single, double, or triple cylindrical heavy wheel mounted horizontally and rotated about their long axis either in opposing pairs or against flat plates, to crush or grind various materials. One of the rollers is run by a motor and the others are rotated by friction as the material is drawn through the gap between the rollers.

Roller mills use the process of stress (which is applied by the rotating wheels) and attrition in milling of solids in suspensions, pastes or ointments, and some solid materials. The rollers rotate at different speeds and the material is sheared as it passes through the gap.

rolling mills: 6 different types of rolling mills [images & pdf]

In this article, youll learn what is Rolling mill and how it works and 6 types of rolling mills with explained with images and also you can download the PDF file of this post.Rolling Mills and TypesContents show1. Rolling Mills and Types2. Types of Rolling Mills2.1. 1. Two High Rolling Mills2.2. 2. Three High Rolling Mills2.3. 3. Four High Rolling Mills2.4. 4. Cluster Rolling Mill2.5. 5. Planetary Rolling Mill2.6. 6. Tandem or Continuous Mill3. ConclusionRolling mill is the extensively used process and the most expensive one in terms of equipment costs. It accounts for almost 90% of the metal produced by forming.Image credit: IndiamartIn the rolling process, the job is drawn through a set of rolls due to interface friction, and the compressive forces reduce the thickness of the workpiece or change in its cross-sectional area. The types of rolls used in rolling mills are depended upon the shape, size and the gap between the rolls and their contour. Because of workability and limitations in equipment, rolling is done in the following steps, that is a number of passes through the rolls may be required to get the required configuration.During rolling initial passes results in a reduction of cross-sectional area, while intermediate passes try to bring the shape closer to the final shape and the final or finishing passes bring the material to the required shape and size. Plates, bars, rounds, structural shapes, sheets and strips can be obtained by rolling.Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Rolling mill is the extensively used process and the most expensive one in terms of equipment costs. It accounts for almost 90% of the metal produced by forming.Image credit: IndiamartIn the rolling process, the job is drawn through a set of rolls due to interface friction, and the compressive forces reduce the thickness of the workpiece or change in its cross-sectional area. The types of rolls used in rolling mills are depended upon the shape, size and the gap between the rolls and their contour. Because of workability and limitations in equipment, rolling is done in the following steps, that is a number of passes through the rolls may be required to get the required configuration.During rolling initial passes results in a reduction of cross-sectional area, while intermediate passes try to bring the shape closer to the final shape and the final or finishing passes bring the material to the required shape and size. Plates, bars, rounds, structural shapes, sheets and strips can be obtained by rolling.Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

In the rolling process, the job is drawn through a set of rolls due to interface friction, and the compressive forces reduce the thickness of the workpiece or change in its cross-sectional area. The types of rolls used in rolling mills are depended upon the shape, size and the gap between the rolls and their contour. Because of workability and limitations in equipment, rolling is done in the following steps, that is a number of passes through the rolls may be required to get the required configuration.During rolling initial passes results in a reduction of cross-sectional area, while intermediate passes try to bring the shape closer to the final shape and the final or finishing passes bring the material to the required shape and size. Plates, bars, rounds, structural shapes, sheets and strips can be obtained by rolling.Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

The types of rolls used in rolling mills are depended upon the shape, size and the gap between the rolls and their contour. Because of workability and limitations in equipment, rolling is done in the following steps, that is a number of passes through the rolls may be required to get the required configuration.During rolling initial passes results in a reduction of cross-sectional area, while intermediate passes try to bring the shape closer to the final shape and the final or finishing passes bring the material to the required shape and size. Plates, bars, rounds, structural shapes, sheets and strips can be obtained by rolling.Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

During rolling initial passes results in a reduction of cross-sectional area, while intermediate passes try to bring the shape closer to the final shape and the final or finishing passes bring the material to the required shape and size. Plates, bars, rounds, structural shapes, sheets and strips can be obtained by rolling.Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Here are the some of similar article you can checkout:Heat treatment: Types, Working and Process of Heat TreatmentMetal Casting Process: Types of Moulding, Sands and Its classification.Types of Rolling MillsFollowing are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Following are the 6 different types of rolling mills used in many industries:Two high rolling millsThree high rolling millsFour high rolling millsCluster rolling millsPlanetary rolling millsTendem or Continuous mills1. Two High Rolling MillsIt contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

It contains two heavy rolls fixed one over the other. The rolls are supported in bearing housed in sturdy upright frames (called stands) which are grouted to the rolling mill floor. The vertical gap between the roll is adjustable. The rolls rotate in opposite directions and are driven by electrical motors.The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

The direction of rotation of rolls cannot be changed, therefore the work has to be fed into rolls from one direction only. If rolling requires more than one pass in the same set of rolls, the material will have to be brought back to the same side after the first pass.2. Three High Rolling MillsIt consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

It consists of three rolls positioned directly over one another as shown in the figure below. The direction of rotation of the first and second rolls are opposite as in the case of two high mills. The direction of rotation (path) of second and third rolls is always opposite to each other.Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Always all three rolls rotate in their bearings in the same direction. The advantages of this will mill is that work material can be fed in one direction between the first and second roll and the return pass can be provided in between the second and third rolls. This results in the transport of material from one side of rolls to the other.Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Read also: List of Mechanical Properties That Every Mechanical Engineer Should Know3. Four High Rolling MillsThe mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

The mill has four horizontal rolls, two smaller diameters and two much larger. The larger rolls are called backup rolls. The smaller rolls are the working rolls, but if they would be thicker in the centre and thinner at either end.Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Backup rolls hold the working rolls and restrict deflection when the material is being rolled. The usual products of these mills are hot and cold plates and sheets.4. Cluster Rolling MillIt consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

It consists of two small diameter working rolls and four or more backing rolls. The larger number of backup rolls provided becomes necessary as the backup rolls cannot exceed the diameter of working rolls by more than 2-3 times.5. Planetary Rolling MillIn the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

In the planetary mill type of rolling machine, a large backup roller is surrounded by a number of planetary working rollers as shown in the figure.Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Each planetary roll gives a continuous reduction. It is employed to reduce large thicknesses in a single pass of a steel strip. Its rolling capacity is higher than cluster machine but less than a tandem rolling machine.6. Tandem or Continuous MillIn this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

In this tandem mill types of rolling mill, It includes of a number of non-reversing two-high rolling mills provide one after other. So that the material can be passed through them all in order.This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

This is only suitable for mass production work, as lower volumes require a quicker change of set up and they will consume a lot of labour and work.ConclusionSo now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

So now, we hope that we have clear all your doubts about Types of Rolling Mill. If you have still any doubts about the Types of Rolling Mill you can contact us or ask in the comments.We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

We have also a Facebook community for you guys. If you want, you can join our community, here is the link toour Facebook group.Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Thats it thanks for reading. If you like our article then please share it with your friends. If you have any questions about any topic you can ask in the comment section.Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Subscribe to our newsletter to get notified when we upload new posts.Email Address SubscribeDownload the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Download the free PDF file of this post by clicking below:Read Next:Milling Machine: Main Parts Working PrincipleDrilling machine Parts, Types, Operations [Complete Guide] with PDFLathe Machine: Parts, Types, Operations, Attachments

Saif M. is a Mechanical Engineer by profession. He completed his engineering studies in 2014 and is currently working in a large firm as Mechanical Engineer. He is also an author and editor at www.theengineerspost.com...