roll crusher for coal

toothed roll crusher for coal preparation plant - ftm machinery

Toothed roll crusher is widely used in coal, metallurgy, mining, chemical industry, building materials, and other industries, and it is more suitable to crush coal in large coal preparation plant and process waste. Toothed roll crusher has a high crushing capacity. The distance between the rollers can be adjusted by hydraulic pressure. The bearing of the toothed roll crusher is centralization lubrication. Whats more, it has the advantages of optimal design, high efficiency, uniform grain, and low cost.

Protective device: The motor is connected with the retarder through hydraulic coupling to avoid dynamic overload. The sensor overload protection is very reliable. If you have mining project or chemical plant, the toothed roller crusher is prepared for you in China Fote.

The toothed roll crusher is suitable for crushing raw coal in coal mines, coal preparation plants and other industries (allowing less than 30% of coal gangue in raw coal). The crusher is also used to break other brittle materials whose hardness is similar to that of raw coal.

It has the characteristics of high efficiency, long life, full sealing, low noise, and uniform granularity. The double-toothed roll crusher is equipped with a scraper to keep the groove and working surface clean. For the toothed roll crusher, the outlet-size depends on the gap between the two rollers, the size of teeth, shape of teeth, and the number.

The double-toothed roll crusher is relatively small in volume. It consists of two tooth rolls that are mounted in parallel and rotate in opposite directions. According to the crushing capacity and the size of the discharging granularity, the two crushing rolls are uniformly filled with brushing teeth.

And the double-toothed roll crusher adopts the operation way of non-circular, non-intermesh and non-uniform, which can enhance the contact face of roller teeth, and avoid material slippage and improve crushing efficiency.

When the toothed roller rotates, the teeth on the surface of the roller can bite the materials and crush them. Each roller crusher of the crushing system is driven by a separate motor. The roller crusher is generally driven by a belt, and it constitutes the deceleration system along with the reducing mechanism.

FTM double-tooth roller crusher for sand making, limestone, rock, clay crushing has a good crushing effect on wet and sticky materials. And adherence or clogging phenomenon never occurs during the work.

The silicon-aluminum raw material is an indispensable calibration material in the dry cement production process. After the mining work, the materials need to be crushed, transported and stored. and then they are sent to the raw material mill for grinding according to an appropriate ratio.

However, the silico-alumina raw materials have strong water storage capacity and high plasticity index, especially for bauxite and marlstone with water content more than 17% and plasticity index generally above 15. Because of the viscosity of materials, it can lead to blockage and arching during the process of crushing, transportation and storage, thus affecting the normal operation of the system.

In order to solve the problem of adherence and clogging of wet-adhesive materials in the crushing stage, FTM toothed roll crusher is used to break the mixture of limestone and marl. In detail, firstly, the wet and dry materials are mixed and crushed, and secondly, the wet-adhesive materials and other limestone materials with lower moisture content are mixed into the crusher. And finally, they are crushed according to an appropriate ratio.

The toothed roller crusher machine has advantages of small volume, large crushing ratio, low noise, simple structure, convenient maintenance, high productivity, uniform particle size of crushed material, low crushing rate, convenient maintenance, sensitive overload protection, safe and reliable.

how a roller crusher crush coal gangue | fote machinery

Coal gangue is an abandoned rock discharged during coal mining and processing. When mining coal, the rock layers or bottom plates from the roof of the coal seam, as well as the various types of rock excavated and blasted from around the coal seam during the excavation are all called coal gangue.

Coal gangue utilization is an important part of comprehensive utilization of resources. The utilization of coal gangue can increase the economic benefits of coal enterprises, improve coal mine production structure and environmental quality.

In China, the total installed capacity of generators of low calorific value fuel such as coal gangue reached 28 million kW, and the single unit capacity was from 6 to 300 MW. The annual utilization of coal gangue was 140 million tons, and the annual power generation was 160 billion kWh.

Since the 1970s, the US Bureau of Mines has sampled and analyzed all coal gangue hills and made comprehensive plans for coal gangue utilization. For example, the heat energy is directly recovered from the burning coal gangue mountain for both recovering the heat and controlling pollution.

Because coal gangue brick products have characteristics of lightweight, high strength, good load-bearing seismic performance, excellent thermal insulation, heat insulation and sound insulation, so it is a broad market.

Road construction and backfilling are also important ways for comprehensive utilization of coal gangue. The use of coal gangue as engineering packing materials do not require an increase in cost and need a large amount of use, which brings good economic efficiency to the coal mine.

There are three main types of coal gangue for chemical use: the first is to extract a rare element in coal gangue by various methods, such as Ga, Se, Ti, Co, etc. The second is to recover beneficial mineral products such as kaolin; the third is the production of silicon, aluminum, sulfur and other inorganic chemical products.

The use of coal gangue fertilizer is mainly based on the fact that coal gangue contains rich organic carbon, and the organic matter content in the soil can be greatly increased after being applied to the soil.

The roll crusher is mainly suitable for fine crushing operations with a feed size of less than 150 mm and a finished product size of 100 mesh to 2 mm. What are the advantages of the roll crusher in use?

Compared with the striking type crushing equipment, the biggest disadvantage of the roll crusher is that the "crushing ratio" is relatively small, the particle size of the product changes with the wear of the gap of the roller, and the crushing effect on the sheet-like material is poor.

Therefore, the most important thing about using the roll crusher is the method of stepwise crushing. When crushing coal gangue, it should go through three processes of "coarse-middle-fine crushing".

The surface of the roll crusher is easily worn to grooves and makes the gap between the rolls larger, thereby reducing the crushing effect. When the roller is new, the gap between the two rollers is the smallest, and the fineness of the crushing is the best.

Therefore, to obtain a good coal gangue crushing product, the work we have to do is to minimize the variation value from fine to coarse, and to control the crushing particle size within the allowable range to ensure the quality of the product.

When crushing coal gangue, to achieve the target particle size, three processes of "coarse-middle-fine crushing" are usually carried out. According to the previous configuration experience, we configure a detailed crushing production line for the 10t/h coal gangue:

Raw material warehouseGZD6502300 vibrating feederPE400600 jaw crusher2PG0640 roll crusher3YK1237 vibrating screenDMC64 dust collectorfinished silo (also several B500 conveyors of different lengths).

It can be seen from the above that when there are three specifications of the finished coal gangue, the jaw crusher can be used as the first crush, and the roll crusher is used for the medium and fine crushing.

As a leading mining machinery manufacturer and exporter in China, we are always here to provide you with high quality products and better services. Welcome to contact us through one of the following ways or visit our company and factories.

Based on the high quality and complete after-sales service, our products have been exported to more than 120 countries and regions. Fote Machinery has been the choice of more than 200,000 customers.

roll crusher with stable performance | fote machinery

Applied materials: coal, pebble, limestone, dolomite, granite, construction waste, pebbles, glass, cement clinker, basalt, iron ore, quartz stone, coal gangue, etc. Its advantages: high capacity, ability to handle wet, sticky feeds.

Roll crusher, as one of the most economical and practical crushers, is designed to handle the first and second crushing of friable minerals and stones such as coal, clay, coal gangue, limestone, slag, cement clinkers, and shale, etc.

According to the number of rollers, the FTM roll crushers can be divided into three types: single roll crusher, double-roll crusher, and multi-roll crusher. And the most common one is double-roll crusher.

Roll crusher is applied more widely than other crushers because of its small volume and cheap price. With the adjustable discharging system, it can be used flexibly in coarse and fine crushing processes of the industries such as cement, chemical engineering, electricity, mining, metallurgy, building materials, and others.

Roll crushers can adjust the wedge device between rollers to control the feed and discharge size of the machine. Also, it is equipped with a spring device to protect the crushing machine and avoid shutdown caused by overload and iron passing.

When the adjustable bolt pulls the wedge upward, the wedge pushes the movable roller away from the fixed wheel, then the gap between the two rollers becomes larger, and the discharge port becomes larger, and vice versa.

The gasket device adjusts the size of the discharge by increasing or decreasing the thickness of the gasket. When the gasket is added, the gap between the two rollers becomes larger, and vice versa.

The unique structure of rollers makes selective crushing of the roll crushing equipment. Since minerals fed are crushed along its internal friable crack, the finished products are uniform with the cube shape.

The minerals are crushed under the force of rollers and machine body, and ores smaller than the gap between roller and machine frame (of single roll crusher) or roller (of multi-roll crusher) will pass directly without repeated crushing.

With the supporting CPU, operators can control roll crushing machines and monitor gaps between rollers, and clean up the crushing cavity through the central control room, which will help save energy of 30% to 50%.

The main working parts of the roller crusher is the cylindrical rollers. The rollers are supported by the fixed and movable bearings, and they are relatively rotating which are driven by the motor. The materials are crushed by the friction of the rotating rollers, and the finished products are discharged from the gap of the rollers.

The spring is used to balance the pressure generated between the rolls. If there are non-crushed materials falling between the two rollers, the compression spring of bearings can be pushed to make a large gap so that non-crushed materials can be discharged immediately.

The quality of the crushers has a great impact on its price. The high-quality equipment will cost more in terms of workmanship, technology, materials, etc. Meanwhile, it will have a long service life, low failure rate, and better performance, and bring more profit to investors.

In 2019, Fote has exported a total of 39 roll crushers to India, Indonesia, Zimbabwe, Vietnam, South Africa, the United States, Pakistan, the Philippines and other countries, mainly for coal, bentonite, rare earth ore, limestone, aluminum, manganese and others.

Exports of mining machinery have been booming in recent years and Fote has already opened markets in Africa, Southeast Asia, etc. Fote Heavy Machinery has supported foreign customers with low-price and high-quality roll crushing equipment, which has been popular among the majority of customers.

In recent years, the Indonesian government has taken actions to improve its infrastructure and promote economic development. As a result, Indonesia's demand for crushers has increased significantly.

The roll crusher produced by Fote has fine finished products and the best effect on sand making for river pebble. Due to its good finished product size, low powder content and low price, it is widely favored by Indonesian customers.

Firstly, Fote Heavy Machinery is a professional manufacturer of roller crushers. In order to improve the company's comprehensive strength, Fote has introduced international first-class production lines on the basis of original techniques.

Secondly, FTM produces various types of crushing equipment that is suitable for crushing, sand making and milling hundreds of minerals, and ensures excellent quality, good performance and low price.

Thirdly, Fote has provided patient and prudential after-sales service and all-round consideration for customers, and actively created high-tech crushing equipment to take the leading position in the international market.

As a leading mining machinery manufacturer and exporter in China, we are always here to provide you with high quality products and better services. Welcome to contact us through one of the following ways or visit our company and factories.

Based on the high quality and complete after-sales service, our products have been exported to more than 120 countries and regions. Fote Machinery has been the choice of more than 200,000 customers.

china crusher manufacturer, cone crusher, rock crusher supplier - atairac engineered products inc(china)

Crusher, Cone Crusher manufacturer / supplier in China, offering Cylinder Stone/Sand/ Aggregate Washing Machine (YTX1530), High Efficiency Spring Cone Crusher Granite, European Type Vibrating Feeder Machinery (ZSW490*110) and so on.

ATAIRAC China is the top3 of mining equipment in China. Our products include feeder, jaw crusher, impact crusher, cone crusher, sand making machine, vibrating screen, sand washing machine, spiral classifier, fine sand recycling device, belt conveyor and other mineral production line assistant equipments. The company has a professional technical team, reliable production and processing equipment, efficient service construction team. Based on understanding customer needs, we are committed to solving ...

high capacity double roll crusher for coal river stone jaw crusher processinging of crushing plant - best stone crusher plant solution from henan dewo

Dewo machinery can provides complete set of crushing and screening line, including Hydraulic Cone Crusher, Jaw Crusher, Impact Crusher, Vertical Shaft Impact Crusher (Sand Making Machine), fixed and movable rock crushing line, but also provides turnkey project for cement production line, ore beneficiation production line and drying production line. Dewo Machinery can provide high quality products, as well as customized optimized technical proposal and one station after- sales service.

The jaw crusher series mobile crushing machine is a new type rock crushing equipment, which can greatly expand the concept of mobile crushing processing areas. Its purpose of design idea stands in customers' position, putting eliminating obstacles about the limitation of crushing space and environmental pollution as the primary solution.

CFTC professional provides you with sand making machine, river pebble sand making machine, vehicle-mounted mobile crushing station, cone crusher, jaw crusher and other sand stone equipment, factory direct sales, quotation discount, factory inspection can bring your own materials free test machine More information can be called or messaged for free.

Mobile Rock Crusher, with capacity ranging from 50t/h to 650t/h, could be used to process hundreds of materials down to 0-10mm, 10-20mm, 20-30mm, 30-40mm separately. And the hottest throughput are found on 80-100t/h, 150-200t/h, 200-300t/h and 300-500t/h.

The jaw crushes the slabs down to a more manageable size, which is then reduced to usable size by a secondary roll crusher. Typically, jaw/roll crushers are used in conjunction with a double deck screen for producing two products for full depth RAP: a fine product (typically < 12.5 mm) and a coarse product (12.5 19.0 mm). Figure 5-9. Jaw crusher.

Hsm Stone Coal Concrete Block Roller Crushing Machine. Hsm stone coal double roller crusher machine for road. theroller crushercan crush materials with middle hardness or less than middle hardness into secondary or fine granularity, such ascrushingmineral, rocks, coke,coal, slag, scoria, and fire-proof material etc. usage and application of joyal good qualitystone roller crusher machinefor ...

roll crushers | mclanahan

Roll Crushers are designed to handle the primary, secondary and tertiary stage crushing of friable materials such as coal, salt, clay, bauxite, limestone and other minerals of similar characteristics in the mining, power generation and numerous other industries. Roll Crushers are one of the most widely used crushers in the mining industry and have numerous advantages, such as high capacity, low headroom, low horsepower, the ability to handle wet, sticky feeds and the generation of minimum fines while producing a cubical product.

The simplified design gives these units excellent reliability and requires very little maintenance. Roll Crushers are designed with built-in tramp relief that allows for the passing of uncrushable materials while continuing operation and returning to the initial product setting.

Since patenting the first Single Roll Crusher in 1894, McLanahan has become an expert and leader in the industry in the design and manufacture of single and two stage Roll Crushers. The selection process for each application is based on extensive equipment knowledge and a wealth of test data developed in our research lab or through on-site testing.

McLanahan offers belt-driven Roll Crushers in four designs: Single Roll, Double Roll, Triple Roll and Quad Roll Crushers, which provide a substantial return on investment by operating at low cost and maximizing yield by generating minimal fines. The rugged design, which incorporates a fabricated steel base frame lined with replaceable abrasion-resistant steel liners, stands up to the toughest mineral processing applications while providing safe and simple operation, including an automatic tramp relief system to allow uncrushable objects to pass while the crusher remains in operation. These crushers are also versatile, allowing for adjustments in roll speeds and gap settings to meet most any application requirement.

Whether the application requires a single-stage or two-stage crusher, the forces necessary to perform the crushing remain the same: a combination of impact, shear and compression. The impact force occurs as the material enters the crusher and is impacted by the rotating roll. Shear and compression forces occur as the feed material is pulled between the crushing plate and/or crushing rolls.

Depending on the feed size, material is fed into the crushing chamber and encounters a single or a pair of rotating rolls. If a two-stage reduction is required, either a Triple or Quad Roll configuration can be used. In this scenario, the top stage of the crusher performs the primary reduction either by crushing the material between the roll and crushing plate or between a pair of rolls. The material is then fed directly between the two bottom-stage rolls for additional processing.

If a single-stage reduction is required, then depending on the feed-to-product-size ratio of reduction, either a Single or Double Roll Crusher can be selected. Regardless of the crusher type selected, Roll Crushers allow for the material to fracture along naturally occurring cleavage lines, which helps with minimizing fines generation.

Yes, it will. When a wet, sticky feed is fed to a two-stage crusher, you run the risk of plugging the crusher between the top and bottom stages. If a wet, sticky feed is anticipated and the ratio of reduction requires two stages of crushing, it is recommended that two separate single stages be used.

A good rule of thumb is: Single Roll Crushers have a 6:1 ratio of reduction, Double Roll Crushers have a 4:1, Triple Roll Crushers have a 6:1 on the top stage and a 4:1 on the bottom stage, and Quad Roll Crushers have a 4:1 on both the top and bottom stage.

Single Roll Crushers are typically used as primary crushers that provide a crushing ratio of up to 6:1. They crush materials such as ROM coal, mine refuse, shale, slate, gypsum, bauxite, salt, soft shale, etc., while producing minimal fines. Designed with intermeshing roll teeth and a curved crushing plate, they are extremely effective in reducing slabby feeds.

Double Roll Crushers provide a 4:1 reduction ratio. They are typically used as a secondary or tertiary crusher for materials such as ROM coal with refuse, limestone, gypsum, trona, shale, bauxite, oil shale, clean coal, coke, salt, quicklime, burnt lime, glass, kaolin, brick, shale and wet, sticky feeds. Each machine is custom engineered with roll elements and tooth patterns selected depending on theapplication requirements to produce a cubical product with minimal fines.

Triple Roll Crushers are ideal for producers who want to accomplish two stages of reduction in one pass. They can be used in coal, salt, coke, glass, and trona operations, among others. Triple Roll Crushers combine a Single Roll Crusher with a Double Roll Crusher to form a crusher that is capable of achieving a 6:1 reduction ratio in the primary stage and a 4:1 reduction in the secondary stage while producing a cubicle product at high capacity.

Quad Roll Crushers are ideal for producers, including those with preparation plants, who want to accomplish two stages of reduction in one pass. They can be used in coal, salt, lime, pet coke and potash operations, among others. Quad Roll Crushers are capable of achieving a 4:1 reduction ratio before feeding the crushed material to the secondary stage for an additional 4:1 reduction to make the final product.

coal crushing: new-type toothed roll crusher vs traditional toothed roll crusher | hxjq

In the coal industry, the requirements for the particle size of the finished product are extremely strict. Generally, the particle sizes of the finished products are between 25 and 70 mm. If it is too large, the furnace will be blocked and further coal processing can't be performed.

Toothed roll crusher is the mature coal crushing equipment applied in the current coal industry, which satisfies all the demands of customers by its advantages of large capacity and low over-crushing rate.

Based on the original toothed roll crushers, HXJQ Mining Machinery has optimized the structure and materials of rollers according to the customers' requirements, so that to adapt the nature of hard gangue and special working conditions and ensure the normal production of coal enterprises.

Traditional toothed roll crusher is usually driven by double-motors. Two sets of motors, couplers and reducers are adopted to drive the independent rollers so that the rollers have the power to crush large coal materials.

The coupler is applied between reducer and rolls to transfer torque. And the toothed rollers and drive system are connected with the machine frame respectively to eliminate the vibrating of toothed roll crusher.

Traditional toothed roll crusher with ring structure has the advantages of stable and reliable performance, and the disadvantages of low wear resistance and hard to replace. Once the traditional toothed roll crusher is damaged, it must be returned to the factory for overhaul.

The traditional rollers are connected by the bolts and tooth-holders, which offers small bearing capacity. Therefore, the traditional toothed roll crushers are mainly applied in the clean-coal crushing process, because the raw coal will cause damage to roll crusher teeth.

In terms of tooth position, the roll crusher teeth are set in the peripheral direction, adopting the setting form of large tooth alternating with a small one. Under the premise of normal discharging size, the crushing force of roller can be improved efficiently, so that to increase the capacity, wear-resistance and service life.

As the picture shows, the new-type tooth-holder adopts the form of regular octagon. The toothed rollers and toothed holders are connected by the flat kay and socket head cap screws (the traditional ones are connected by bolts).

The contacted areas between tooth and toothed holders are processed and improved completely, and torque is transferred by flat key so that can prevent the socket head cap screws from the shearing force of coal materials. And the screws can be firmer and more reliable.

Meanwhile, the fastening bolt and the toothed roller holder are connected by the screw fastening blocks, which makes that the joint strength is ensured, and the interchangeability and the replaceability are also reliable.

The teeth are the main wearing parts of the toothed roll crusher, so it is very necessary to choose a suitable material. Therefore, it is required that the material should have enough hardness, toughness, impact resistance and wear resistance. Also, the following machinability and weldability should be considered.

When parts of high manganese steel are impacted repeatedly, the surface of parts gets changed, and the hardness increases rapidly, which can reach up to HRC54. It will improve the wear resistance significantly, but the inside of parts keeps flexibly. These are the main features of high manganese steel.

However, the toothed roll crushers crush coal materials by shearing and stretching, along with less impacting and squeezing, which makes high manganese steel can't play its advantages to enhance the hardness and strength. Therefore, high manganese steel is not suitable for making teeth.

To better improve the wear-resisting performance of teeth, traditional toothed roll crusher always adopts the low-alloy quenched and tempered steel as the material to make tooth of roll crushers. In general, 40 Cr is used to process the tooth. After processing, the compressive strength and the service life of tooth are improved.

However, since there are only a few millimeters thick wear-resisting layer in the surface of the tooth, it is required to be overlaid frequently in the process of use, which brings a large workload to workers.

The teeth of the new toothed roll crusher adopt the integral casting molding process, optimizes the proportion of the main elements such as C, Cr, Mn, Mo, Si, Ni. The medium carbon bainitic steel is selected finally to be the material of toothed roll.

The medium carbon bainitic steel has good hardenability. After quenching and tempering heat treatment, bainite with high hardness and wear resistance is processed. It has an excellent comprehensive performance of HRC50 hardness and compressive strength of 1500 MPa.

In addition, the material of the entire toothed roller structure, including the toothed roller, the toothed roller holder and the threaded fastening block, is reasonably matched, so that the strength and hardness of each component are more balanced and reasonable.

The raw coal is first crushed to below 300mm by the jaw crusher, and then crushed to below 70mm by a toothed roller crusher, and then transported to the coal storage bin by the belt conveyor. After screening, the final product of 25~70mm is sold to the chemical company.

The customer said it requires technical improvement urgently in their worksite urgently to reduce the operating cost of the enterprise and the labor intensity of the workers and to ensure the normal operation of the production system.

Since the new toothed roller crusher was put into use, the equipment has been running stably, the discharge size of the products is significantly improved, the over-crushing rate reduces, and the block-forming rate is highly increased (see the following table).

It can be seen from the above table that the difference between the qualified products before and after the replacement is 18.2%, which greatly improves the output of qualified products and creates great economic benefits for the enterprise.

In addition, the new toothed roller crusher has high wear resistance, and the fastening bolt is not easy to loosen, which reduces a large amount of maintenance time, the labor intensity of workers, and the maintenance cost of the coal crushing process.

With the transformation and upgrading of the coal industry, it is an inevitable trend to vigorously develop coal chemical industry. The coal chemical industry has strict requirements on the particle size of coal, which puts higher requirements on the crushing equipment.

The new toothed roller crusher can optimize the crushing operation of the raw coal by a series of optimizations on the structure and material of the toothed roller. It has a high block rate and a small maintenance amount. With the obvious technical advantages, the promotion prospects of new-type toothed roll crusher are broad.

roll crusher - an overview | sciencedirect topics

Roll crushers are generally not used as primary crushers for hard ores. Even for softer ores, such as chalcocite and chalcopyrite, they have been used as secondary crushers. Choke feeding is not advisable as it tends to produce particles of irregular size. Both open and closed circuit crushing is employed. For close circuit the product is screened with a mesh size much less than the set.

Figure6.4 is a typical set-up where ores crushed in primary and secondary crushers are further reduced in size by a rough roll crusher in an open circuit followed by finer size reduction in a closed circuit by a roll crusher. Such circuits are chosen as the feed size to standard roll crushers normally does not exceed 50mm.

A distinct class of roll crushers is referred to as sizers. These are more heavily constructed units with slower rotation, and direct drive of the rolls rather than belt drives. They have a lower profile, allowing material to be easily fed by loaders, and are a good choice for portable crushers at the mine that reduce the coal in size for conveying to the preparation plant. An example of these units is shown in Fig.9.4.

9.4. (a) Primary sizer with attached feeder. The large motors and gearboxes drive the relatively low-speed toothed rolls that break the coal. (b) Haulage truck dumping coal directly into the feed hopper for a primary sizer, which discharges onto a product belt. (c) Tertiary sizer for crushing coal to the desired size for a preparation plant.

Their lower speeds are claimed to reduce fines generation, while lending themselves to high throughput applications. Sizers can either have the rolls rotate towards each other to carry feed between the rolls to be broken, or can be constructed as tertiary sizers with the rolls rotating away from each other. With tertiary sizers, feed coal is added between the rolls, and much of the fine material falls through. The coarser material is then carried to the outside to be broken against fixed sizing combs. This design increases the capacity by producing two main product streams instead of one, and also minimizes overcrushing by removing a large fraction of the fines. Tertiary sizer capacities range from 440 tons/h (400 metric tons/h) for 2448 inch (61122cm) rolls producing a 2-inch (5cm) product, up to 3968 tons/h (3600 metric tons/h) for 2096 inch (51244cm) rolls producing a 10-inch (25cm) product (Alderman and Edmiston, 2010).

A typical coal handling package using sizers would comprise a dump pocket discharging to a primary sizer discharging to a product belt, as shown in Fig.9.4b. This product belt would then feed a secondary or tertiary sizer, such as is shown in Fig.9.4c, which may include intermediate screening to remove product prior to subsequent stages of breakage. Typical size ranges would start with run-of-mine coal feeding to the primary sizer at 2000mm, and reducing to 350mm. The secondary sizer would receive this coal and discharge at a nominal 125mm, followed by a tertiary sizer/screen combination to generate a 50mm topsize preparation plant feed (FLSmidth, 2011).

The intermediate crushing in the cut roll crusher is mainly used for the crushing of brittle materials like concrete and clay sintered bricks, along with the compression of rough materials like wood and fabric (to avoid being too small in size) after the coarse (primary) crushing. The selective crushing in this process is good for the separation of impurities. Impact crushers are commonly applied in intermediate crushing. However, when used in crushing of mixed C&D waste, the wood and fabric materials will be broken and mixed in recycled aggregate materials by the high-speed operating rotors and are difficult to be separated.

Although not widely used in the minerals industry, roll crushers can be effective in handling friable, sticky, frozen, and less abrasive feeds, such as limestone, coal, chalk, gypsum, phosphate, and soft iron ores.

Roll crusher operation is fairly straightforward: the standard spring rolls consist of two horizontal cylinders that revolve toward each other (Figure 6.14(a)). The gap (closest distance between the rolls) is determined by shims which cause the spring-loaded roll to be held back from the fixed roll. Unlike jaw and gyratory crushers, where reduction is progressive by repeated nipping action as the material passes down to the discharge, the crushing process in rolls is one of single pressure.

Roll crushers are also manufactured with only one rotating cylinder (Figure 6.14(b)), which revolves toward a fixed plate. Other roll crushers use three, four, or six cylinders, although machines with more than two rolls are rare today. In some crushers the diameters and speeds of the rolls may differ. The rolls may be gear driven, but this limits the distance adjustment between the rolls. Modern rolls are driven by V-belts from separate motors.

The disadvantage of roll crushers is that, in order for reasonable reduction ratios to be achieved, very large rolls are required in relation to the size of the feed particles. They therefore have the highest capital cost of all crushers for a given throughput and reduction ratio.

The action of a roll crusher, compared to the other crushers, is amenable to a level of analysis. Consider a spherical particle of radius r, being crushed by a pair of rolls of radius R, the gap between the rolls being 2a (Figure 6.15). If is the coefficient of friction between the rolls and the particle, is the angle formed by the tangents to the roll surfaces at their points of contact with the particle (the angle of nip), and C is the compressive force exerted by the rolls acting from the roll centers through the particle center, then for a particle to be just gripped by the rolls, equating vertically, we derive:

The coefficient of friction between steel and most ore particles is in the range 0.20.3, so that the value of the angle of nip should never exceed about 30, or the particle will slip. It should also be noted that the value of the coefficient of friction decreases with speed, so that the speed of the rolls depends on the angle of nip, and the type of material being crushed. The larger the angle of nip (i.e., the coarser the feed), the slower the peripheral speed needs to be to allow the particle to be nipped. For smaller angles of nip (finer feeds), the roll speed can be increased, thereby increasing the capacity. Peripheral speeds vary between about 1ms1 for small rolls, up to about 15ms1 for the largest sizes of 1,800mm diameter upwards.

Equation 6.6 can be used to determine the maximum size of rock gripped in relation to roll diameter and the reduction ratio (r/a) required. Table 6.1 gives example values for 1,000mm roll diameter where the angle of nip should be less than 20 in order for the particles to be gripped (in most practical cases the angle of nip should not exceed about 25).

Unless very large diameter rolls are used, the angle of nip limits the reduction ratio of the crusher, and since reduction ratios greater than 4:1 are rare, a flowsheet may require coarse crushing rolls to be followed by fine rolls.

Smooth-surfaced rolls are usually used for fine crushing, whereas coarse crushing is often performed in rolls having corrugated surfaces, or with stub teeth arranged to present a chequered surface pattern. Sledging or slugger rolls have a series of intermeshing teeth, or slugs, protruding from the roll surfaces. These dig into the rock so that the action is a combination of compression and ripping, and large pieces in relation to the roll diameter can be handled. Toothed crushing rolls (Figure 6.16) are typically used for coarse crushing of soft or sticky iron ores, friable limestone or coal, where rolls of ca. 1m diameter are used to crush material of top size of ca. 400mm.

Wear on the roll surfaces is high and they often have a manganese steel tire, which can be replaced when worn. The feed must be spread uniformly over the whole width of the rolls in order to give even wear. One simple method is to use a flat feed belt of the same width as the rolls.

Since there is no provision for the swelling of broken ore in the crushing chamber, roll crushers must be starvation fed if they are to be prevented from choking. Although the floating roll should only yield to an uncrushable body, choked crushing causes so much pressure that the springs are continually activated during crushing, and some oversize escapes. Rolls should therefore be used in closed circuit with screens. Choked crushing also causes inter-particle comminution, which leads to the production of material finer than the gap of the crusher.

The objective of sample preparation is to prepare test samples from a parent sample or individual primary increments, Fig.5.19 for analysis. Sample preparation includes all procedures that a sample is subjected to in order to produce a reduced mass of sample (analysis sample) that is representative of the parent sample and from which subsamples of relatively small mass can be used directly for analysis. Samples for general analysis (proximate, ultimate, calorific value, total sulphur, etc.) are typically milled samples with 95% passing 0.212mm. Standard AS4264.1 stipulates that the minimum mass required for general analysis is 30g.

However, some laboratory analyses will require larger sample masses. Some examples from AS 4264.1 include Hardgrove grindability index (AS 1038.20) which requires 1kg at 4.75mm top size, and total moisture (AS 1038.1 Method A and B) 300g at 4mm. However, the principles of preparing a representative analysis sample from the original coal sample are the same.

Taking the ash determination as an example: 1g of coal is used in a single ash determination, and that 1g has to be representative of the coal sample. At a top size of 0.212mm the sampling constant, Ks, for most coals will be very small and this constant combined with a 1g mass of coal enables the variance contribution from the IH of the analysis sample to be almost insignificant and therefore a high level of precision can be expected.

Apart from exploration samples, most samples received by laboratories are from mechanical sampling systems at coal handling facilities at mine sites, ports or power stations. In some areas where coal is being sold across land boarders such as the MongolianChinese border, most samples will be extracted directly from haulage trucks. Many samples, such as ship loading samples and some coal preparation plant samples, are produced by multistage mechanical sampling systems. Other samples may be produced from single-stage samplers. As a result, laboratories can receive samples in a wide range of conditions, most importantly sample mass, moisture content and particle size distributions. Sample preparation procedures have to be tailored to suit the samples and the proposed testing and analyses procedures that the sample has been collected for.

In some instances the particle size reduction may be omitted before sample subdivision, for example at the first stage after collection of the primary increment. However, generally before subdivision (subsampling) the particle size should be reduced.

In each case at every stage, the process recognises the relationships between the number of increments, sample mass and particle size to sampling variance, as each stage is a standalone sampling exercise.

Hammers mills comprise a set of swinging hammers attached to a rotating shaft (Fig.5.22). Typically, they are fed a 4mm top size coal to produce analysis samples with >95% passing 0.212mm. They have a device for feeding the coal into the mill. This is often a screw-type feeder. They also usually have a screen on the outlet to ensure that the entire sample achieves a specific top size. Hammer mills tend to generate excessive fines and should not be used in some instances, such as preparation of samples for petrographic analysis and Hardgrove grindability index determination.

Ring mills comprise a cylindrical canister and lid, a steel ring, and a smaller steel cylinder that fits inside the canister (Fig.5.23). The coal is placed in the canister with the ring and the cylinder, and the lid is attached. This is then placed in a jig that moves the canister in a circular motion. The movement of the various metal components within the canister crushes the coal. There is some concern that these mills can become heated and that this may affect the coal quality, particularly CSN values. This type of mill is particularly useful for crushing low mass samples as sample loss is kept to a minimum. Automated ring mills have been in use in laboratories handling large sample volumes to ensure consistent milling and improved productivity.

Roll crushers are comprised of two steel cylinders (Fig.5.24). The coal is crushed as it passes between the cylinders. This type of crusher is useful when preparing samples with a minimum of fines generation.

Incremental division is a manual method of subdivision that can provide precise subsamples. This method requires that the coal is well mixed prior to division. The coal is spread onto a flat surface in the form of a rectangle in a thickness approximately three times the nominal top size of the sample. A grid pattern is marked out on the sample (usually composed of at least 20 rectangles in a 54 grid) and a single increment is obtained from each square. The increment is removed from the sample using a suitable scoop and bump plate to prevent the increment from falling out of the scoop. Incremental division is used almost exclusively in obtaining the final (0.212mm) laboratory sample after the hammer mill operation, because of excessive dust losses by other methods.

Rotary sample division (rsd) is the most common method for subdivision of large samples in coal laboratories. The rotary sample divider (Fig.5.25) comprises a feed hopper, a device for feeding the coal at a constant rate (usually a vibratory feeder) and a number of sector-shaped canisters formed into a cylinder on a rotating platform. The uniform coal stream produces a falling stream of coal that is collected in the rotating canisters, dividing the sample into representative parts.

As the coal particles move through the feed hopper there is a high potential that some segregation and grouping will occur. To counter the effect that this may having on sample preparation variance it is advisable to ensure that each canister cuts the falling stream at least 20 times, i.e. there are at least twenty rotations of the turntable as the coal flows into the canisters. Additionally, it is a good practice to combine material collected in two or more canisters to form the divided increment or subsample. When doing so, canisters that are opposite each other in the rotary sample divider should be selected for recombination. The machine pictured in Fig.5.25 is set to divide a sample into eight divisions. If the requirement was to extract a quarter of the sample for analysis, two of the 1/8th divisions would be recombined.

Riffles (Fig.5.26) are less regularly used in laboratories. Riffles divide the coal into halves by allowing the coal to fall through a set of parallel slots of uniform width. Adjacent slots feed opposite containers. The width of the slots should be at least three times the nominal top size of the coal. There should be at least eight slots for each half of the riffle.

Fractional shovelling may be used for subsampling when a large rotary sample divider is not available. In this process, the coal is formed into a conical heap. Successive shovels of coal are removed from the base of the heap and are placed into daughter heaps. The shovels of coal should be allocated consecutively and systematically to each daughter heap.

Shredding rubber waste reduces the volume of used tires. Generally, the cost of shredding increases with the need to obtain pieces as small as possible. For grinding, rubber wastes are initially processed through mechanical cutters, roll crushers and screw shredders. To obtain finer particles, shear crushers and granulators are used. The final processing of rubber wastes is with high-temperature shredding equipment, such as rotary shredders, where degradation occurs during compression simultaneously with shear and wear (Mikulionok, 2015). In the initial phase, shredding rubber wastes results in dimensions of approximately 7.6210.16cm. These pieces are then placed in cutters that reduce the size to 0.630.63cm (Rafique, 2012).

Granulators are used in the second step of the recycling process, where pieces of waste tyres are grinded in the large-sized granulators to produce a large quantity of granules. The use of pulverises can reduce the rubber granulated material into fine powder. The rubber particles size can range from a few micrometres up to centimetres.

Rotary Breakers (Fig. 1). The rotary breaker serves two functionsnamely, reduction in top size of ROM and rejection of oversize rock. It is an autogenous size-reduction device in which the feed material acts as crushing media.

Roll Crusher. For a given reduction ratio, single-roll crushers are capable of reducing ROM material to a product with a top size in the range of 20018mm in a single pass, depending upon the top size of the feed coal. Double-roll crushers consist of two rolls that rotate in opposite directions. Normally, one roll is fixed while the other roll is movable against spring pressure. This permits the passage of tramp material without damage to the unit. The drive units are normally equipped with shear pins for overload protection.

Process is designed to reduce the size of large pieces with minimum production of dust. Two main types of breakers are used in Great Britain, viz. (a) Pick Breaker and (b) Bradford Breaker. Other crushers commonly used are jaw crushers, roll crushers, disc crushers, cone crushers and hammer crushers.

Pick breakerdesigned to imitate the action of miners' picks. Strong pick blades are mounted rigidly on a solid steel frame moving slowly up and down. Coal passes under the picks on a slowly moving horizontal plate conveyor belt. The amount of breakage is roughly controlled by the height to which picks are raisedupper limit is 0.5 m Typical performances: 450 ton/hr with a 2-m-wide machine. Size reduction from 500 mm to 300 mm. Several machines may be placed in series, with screens in between to remove fines. Main advantageminimum production of fines can be achieved. Fines production is controlled by the diameter and spacing of picks. Reduction in diameter and increase in spacing, decrease the proportion of fines.

Bradford breakerScreens break and removes large pieces of accidental material, e.g. pit props, chains or tramp iron, in one operation. Consists essentially of a massive cylindrical screen or Trommel, with fins fitted longitudinally inside the screen. These raise the lumps of coal as the cylinder rotates, until they fall, break, and are screened. Unbroken material passes out of the end of the cylinder. Production of fines is also small. Capacity of machine: up to 600 ton/hr.

Blake jaw crusher. Consists of a heavy corrugated crushing plate, mounted vertically in a hollow rectangular frame. A similar moving plate (moving jaw) is attached at a suitable angle to a swinging lever, arranged so that the reciprocating movement opens and closes the gap between the plates, the greater movement being at the top. The machine is available with top opening up to 2 2.7 m. Usual capacity up to 300 ton/hr. Horsepower required: up to 150.

Corrugated and toothed roll crushers. Two heavily toothed, or corrugated, cylindrical rollers (Fig. 10.1) are mounted horizontally and revolve in opposite directions. (Towards each other at the top side or nip, one being spring loaded.) Alternatively, a single roll may revolve against a breaker plate. Capacity of a 1.5 m-long machine with a 300 mm opening and roll speed 40 r.p.m. is about 350 ton/hr, with a power consumption of about 200 h.p. Best results are obtained by the use of several rolls in series, with screens between.

Run-of-mine coal produced by mechanized mining operations contains particles as small as fine powder and as large as several hundred millimeters. Particles too large to pass into the plant are crushed to an appropriate upper size or rejected where insufficient recoverable coal is present in the coarse size fractions. Rotary breakers, jaw crushers, roll crushers, or sizers are used to achieve particle size reduction. Crushing may also improve the cleanability of the coal by liberating impurities locked within composite particles (called middlings) containing both organic and inorganic matter. The crushed material is then segregated into groups having well-defined maximum and minimum sizes. The sizing is achieved using various types of equipment including screens, sieves, and classifying cyclones. Screens are typically employed for sizing coarser particles, while various combinations of fine coal sieves and classifying cyclones are used for sizing finer particles. Figure 2 shows the typical sizes of particles that can be produced by common types of industrial sizing equipment.

The sponge masses as produced by vacuum distillation have to be prepared before melting. The nine ton mass of sponge has to be crushed to about 12mm size pieces. The sponge in contact with retort wall and the push plates have a high likelihood of contamination with iron and nickel since these metals are soluble in titanium. The top of the mass may also have some contamination of iron and nickel from reaction with the radiation shield and substoichiometeric chlorides. To remove this contamination the outer skin of the sponge mass is removed by use of powered chisels. This material is downgraded from aerospace use and used in less critical applications. The sponge mass then is sliced radially to one to 5cm sections with a large guillotine or similar blade. The bottom section of the mass is removed first as this likely has the most amount of iron incorporated into the sponge. The sponge mass is removed from the working table, so this material can be segregated from the balance of the mass. At this point the mass is placed back on the table, sliced and then sent to a crushing circuit. Titanium sponge is malleable material, thus traditional mineral processing equipment such as roll or jaw crushers are not as effective as high shear shredding machines such as rotary shears or single rotor/anvil shears in preparing sponge with limited very fine particle generation.

Dust generation in the crushing process is a very important aspect of operation. Control of the dust by collection and washing of equipment on a periodic basis is very important to reduce the risks of fire in the processing of sponge. Care has to be taken to avoid working on equipment when dust present as titanium metal fires are difficult to extinguish; a class D extinguisher or rock salt are used to suppress the first. The high temperature of the fire and the low melting point of iron-titanium eutectic can result in melting of equipment, supports or piping in these plants if a fire does occur.

The core of the sponge mass has the lowest level of metal contamination. To harvest the material for applications that need low iron and low nickel levels, it is necessary to core the mass. This is done in several ways; the mass can be upended and the guillotine blade can be used to remove thick layers of outer skin, or chisels can be used to remove the outer layers. Control of the lot by separation during the crushing campaign is used to separate the high-purity products from the normal grades of sponge. Control of the nickel level in the magnesium used in the reduction is also important. Removal of as much stainless steel in piping, retorts and metal reservoirs is also important, as nickel in the magnesium will be incorporated into the sponge. Small concentrations of nickel in magnesium can take a long time to be purged from the process. Control of the quality of magnesium used for make up in the VDP process is as important, as some magnesium can be contaminated with nickel during production. Iron is not as significant an issue as its solubility in magnesium is low.

7 things youd better know about coal double roll crusher machine - hongxing machinery

Roll crusher has a simple structure with a less excessive crushing phenomenon. The tooth shape, size, and arrangement of roll surface can be changed with the properties of the material, and the medium-hard and soft ore can be crushed in medium and fine. And, whats more, the roll crusher equipment is mainly composed of a roller wheel, roller bearing, pressing and regulating device and driving device. Generally, a double roll crusher often crushes aggregate materials by two rolls, it is suitable for medium and soft stone materials, especially for coal materials.

The driving mechanism is driven mainly by two motors, which is dragged to the slot wheel through a triangular belt and rotates according to the relative direction. When the material is broken, the material passes through the roller through the feeding port, which is crushed and broken, and the finished product is discharged under the chassis. In order to be safe, the transmission part should install the safety cover according to the actual situation. Outstanding advantages of coal double roller crushers: Excellent and efficient crushing TEMP effect:The output of Hongxing double roll crusher is 1.5 times of that of conventional crushers, and the particle size of the finished stone is uniform, the size is reasonable, and the dust content is low. Production cost: There is a broken tooth ring on the double roll crusher, and the wear of the double roll crusher sleeve can be replaced to a certain extent, so as to reduce the downtime and the production cost. Safe and stable operation: The limit rectangular hydraulic coupler not only absorbs the impact force at the time of crushing, but also ensures the smooth operation of the machine, and also has the function of safety protection for the machine. Reduce over crushing and wear parts: The dual function of crushing and screening reduces the over-crushing and energy consumption of the material, prolongs the service life, and has the TEMP effect of shearing and stretching crushing. The material is not easy to be blocked : non-equal round, non-meshing, and non-constant speed operation of two rollers and the phenomenon of material blockage of the roller crusher will be reduced.

Roll crusher is also called double roll crusher, which is mainly used for fine crushing operation with ore particle size less than 80mm. The utility model has the advantages of small volume, large crushing ratio, low noise, simple structure, and convenient maintenance. The particle size of the broken material is uniform, the over-crushing rate is low, and the particle size of the finished product is 0.5 40 mm.

The tooth roll crusher is mainlymade upof transmission device, frame part, crushing roller, mechanical spring device, linkage mechanism and so on. It is suitable for coal, metallurgy, mining, chemical industry, building materials, and other industries, and toothed roll crusher is more suitable for the crushing of raw coal (including gangue) in large coal mines or coal preparation plants. The crushing capacity of a toothed roll crusher is large, and the limited distance between motor and reducer to prevent power overload and sensor overload protection, which is safe and reliable.

One of the most simple and intuitive differences between the double roll crusher and the toothedroll crusher is the tooth, in other words, the toothedroll crusher has the tooth, double roll crusher doesnt have the tooth. On the other hand, it is possible to distinguish from the mode operation of the apparatus, the drive mechanism of the roller crusherisdriven by two motors, by means of a triangular belt drive to the sheave, and rotating in a relativedirection. When the material is crushed, the material passes through the roller wheel from the feeding port, is crushed by the rolling, and the broken finished product is discharged from the bottom of the bottom frame.

Hongxing tooth roller crusher adopts special wear-resistant tooth roller to rotate at high speed, and the material is split and broken (the traditional tooth-roller crusher is crushed by low-speed extrusion), and the mechanism of high productivity is formed. The pitch of the toothedroller machine is adjusted hydraulically, and the bearing of the HXJQtoothedroller shaft is lubricated. Generally, the toothed roll crusher has the designof optimization, the tensile shear selection, high-efficiency, low-consumption anduniform discharginggranularity.

Recently, an Indian customer named Jim has come to HXJQ corporation for purchasing double roll crushers, at first, HXJQ coal roll crusher price has surprised him a lot, cause the roll crushers not only has excellent quality but also great advantages (comparing to other roll crushers). After a conversation with our salesman, Jim has adopted the advice raised by the salesman. Additionally, Jim has also seen the worksite of our crushers on HXJQ website.

There are many double roll crusher manufacturersproducing this kind of crusher machine, one of the most popular mining crushers manufactures is China HXJQ. As we all know, Hongxing Machinery offers multiple types of double roll crushers, you can choose your ideal crushers according to double roll crushers catalog. There are many double roll crushers for sale.

coal crusher, coal crushing machine, coal crusher manufacturer, coal crusher price - ftm crusher company

Since the compression strength of coal is about 5-50, general crusher is able to deal like jaw crusher, impact crusher and roll crusher, etc. However, there exist special requirements for processing and using the coal, thus Fote technically produces a hammer coal crusher.

1. If you have various demands for the particle size of finished products, the Fote hammer coal crushing machine will help you. Hammer coal crusher machine has advantages of high production capacity and finished product is about 35mm, and its adjustable to be changed in different models of primary crushing, secondary crushing and fine crushing.

2. As we all know, the coal is valued and we should use effectively. If the coal is over-crushed, a lot of coal ash will appear. While the hammer coal crusher uses the active forces of hammer to crush coal, you will love this hammer coal crushing machine since it can reduce the appearance of coal ash.

3. If you are in the field of coal crushing, you must be troubled with the coal with high water content. While the hammer coal crusher machine can crush both dry and wet coal. It is completely suitable to the open-pit mining work.

If you need the latest price list, please leave us a message here, thank you! We guarantee that your information will not be divulged to third parties and reply to you within 24 hours. Tell us your needs, there will be more favorable prices!

double roll crushers | mclanahan

Double Roll Crushers typically follow a primary or secondary crusher and are used for secondary and tertiary reduction of various minerals, such as ROM coal, clean coal, limestone, gypsum, trona, shale, bauxite, oil shale, coke, salt, lime, glass, kaolin, brick, shale and wet, sticky feeds. They are one of the most widely used crushers in the mining industry and have numerous advantages, such as high capacity, low headroom, low horsepower, the ability to handle wet, sticky feeds and the ability to produce a cubical product with minimum fines generation. Roll diameters and widths are dictated by the feed size, product size and capacity. The rule of thumb for the Double Roll Crushers ratio of reduction is 4:1.

The simplified design gives these units excellent reliability and requires very little maintenance. The crushers are designed with built-in tramp relief that allows for the passing of uncrushable objects while remaining in continuous operation and returning to the initial product setting. With a variety of roll surface designs, this crusher is capable of producing a much finer product. Since each machine is custom engineered, roll elements and tooth patterns are selected depending on each unique application.

McLanahan Double Roll Crushers feature slower roll speeds and a larger surface area to add prolonged life to the crushing elements, resulting in less maintenance downtime and decreasing your cost per ton. Double Roll Crushers generate minimum fines while producing a cubical product.

McLanahan Double Roll Crushers are designed for safety and many years of rugged operation. Effective tramp protection against non-crushable material is provided by an automatic spring-and-toggle system. This allows a movable roll to open, pass the material and return to its original setting for continued operation. Hydraulic product size adjustment allows producers to adjust for changes in product size requirements or to compensate for roll wear.

Operating Double Roll Crushers is quite simple. Whether it is a single or dual drive arrangement, the rolls are powered by electric motors and V-belt drive configurations, resulting in reliable and quiet operation. If it is a single drive arrangement, power is transferred from the driven roll to the non-driven opposing roll by an interstage V-belt drive. If it is a dual drive configuration, each roll is powered independently through a motor and V-belt drive.

During normal operation, the material is fed between the crushing rolls. A combination of compression and shear forces created between the opposing rolls reduce the feed material to the desired product size while producing a cubicle product with minimum fines.

McLanahans mechanical tramp relief systems employ a spring-and-toggle mechanism that activates whenever an uncrushable object enters the crushing chamber. Once an excessive force is applied to the movable roll, the toggles break open to allow the uncrushable item to pass. The high torsion springs then close the toggles, returning the movable roll to the previous setting. The crusher continues to operate uninterrupted.

When an uncrushable object, such as metal, roof bolts/timbers, etc., enters the crusher and the force necessary to crush this material is greater than the crushing forces of the crusher, the crusher allows the moveable roll to open and pass the tramp material and then return to its previous setting and remain in operation.

Depending on the customers desired product size and fines consideration, Mineral Sizers or Hammermills could be considered. The reasons people would consider a Roll Crusher over these alternative technologies include lower power requirements, less fines generation and costs.

Black Diamond Double Roll Crushers are the most versatile and popular model of McLanahan Double Roll Crushers. Ideal for secondary and tertiary crushing applications where product requirements drop down to (6mm), Black Diamond Double Roll Crushers are most commonly used to crush clean coal or friable materials with little or no hard refuse. They are available with single or dual V-belt drive.

Heavy-Duty Double Roll Crushers are ideal for the primary, secondary and tertiary crushing of limestone, gypsum, ROM coal, etc. where higher compressive strength material is anticipated. Due to the V-belt drive design, a lower horsepower is required compared to other crushers designed for the same applications.

Shalemaster Double Roll Crushers are driven mechanically with V-belt drives and gear reducers. They offer the same durability as other McLanahan Double Roll Crushers but are designed to handle wet, sticky feeds such as soft shale, kaolin and clay. The Shalemasters special tooth design and differential roll speeds provide optimum performance against plugging and other problems often associated with handling sticky materials.

Typically used as secondary or tertiary crushers, McLanahan Double Roll Crushers provide a 4:1 reduction ratio and can be used following other McLanahan equipment, such as Feeder-Breakers, Rotary Breakers, primary DDC-Sizers, or Single Roll Crushers, when further reduction of primary crushed material is required. Each Double Roll Crusher is selected and engineered for its specific application, thus roll elements and tooth patterns are selected based on the customers unique applications and designed to produce a cubical product with minimal fines.

high efficiency double roller crusher for coal slag plant - henan factory supply best price portable jaw stone crushers plant

Dewo machinery can provides complete set of crushing and screening line, including Hydraulic Cone Crusher, Jaw Crusher, Impact Crusher, Vertical Shaft Impact Crusher (Sand Making Machine), fixed and movable rock crushing line, but also provides turnkey project for cement production line, ore beneficiation production line and drying production line. Dewo Machinery can provide high quality products, as well as customized optimized technical proposal and one station after- sales service.

High Capacity Coal Breaking Double Roller Crusher For Open Pit Deposit , Find Complete Details about High Capacity Coal Breaking Double Roller Crusher For Open Pit Deposit,High Capacity Coal Crusher,Roller Crusher,Coal Breaking Crusher from Crusher Supplier or Manufacturer-Tangshan Tianhe Environmental Protection Technology Co., Ltd.

The toothed roll crusher is suitable for crushing raw coal in coal mines, coal preparation plants and other industries (allowing less than 30% of coal gangue in raw coal). The crusher is also used to break other brittle materials whose hardness is similar to that of raw coal. It has the characteristics of high efficiency, long life, full ...

1. Adopting high pressure crushing theories to material so as to achieve higher crushing efficiency, higher crushing ratio and wider adaptation. 2. Automatic adjusting roll surface interval to keep the set crushing force stable, product shape better and granule finer. 3.

High capacity double toothed roll crusher with competitive . high capacity double toothed roll crusher with competitive price, us $ 15,000 100,000 / set, new, roller crusher, coal fired power plant,coal mining,limestone mining,cement plant.source from tangshan tianhe environmental protection technology co., ltd. on alibaba.

300Tph High Efficiency Steel Slag Comprehensive Recycling Line Dewo machinery can provides complete set of crushing and screening line, including Hydraulic Cone Crusher, Jaw Crusher, Impact Crusher, Vertical Shaft Impact Crusher (Sand Making Machine), fixed and movable rock crushing line, but also provides turnkey project for cement production ...

roll crusher manufacturer & design | williams crusher

You are now leaving our website and entering a website hosted by another party. Please be advised that by continuing you will no longer be subject to the protection of our privacy and security policies. First Bank does not guarantee the experience and content accuracy of the new website you will visit.

Williams is an industry-leading roll crusher manufacturer and designer for high-quality roll crushers with desirable benefits such as high throughput capacity, minimal maintenance requirements, low cost per ton operation, and more. Learn more about our heavy-duty roll crushers below or contact our sales engineers to talk about your application needs.

A combination of impact, shear, and compression are the forces necessary to perform the crushing and size reduction in a Williams roll crusher. The material enters the roll crusher machine and is impacted by the roll as it rotates. Then, as the material is pulled between a crushing plate or rolls, shear and compression forces act upon the material. The rolls act as flywheels, contributing to smooth operation and efficient use of power. Roll crushing surfaces operate at a fixed distance apart, as opposed to the continually changing distances in a jaw or cone crusher. This creates a more consistent product size.Roll crushers are low in profile and relatively easy to install. They can be fed with a minimum of headroom, or even choke fed. Adjustments are simple andinternal parts are readily accessible.

Typical feed materials for Williams Roll Crushers include: bauxite, cement clinker, chalk, cinders, clay, coal, glass, gypsum, limestone, burnt lime, rock salt, sandstone, shale, sulfur ore, sea shells, and sewer sludge clinker. Single Roll Crushers, sometimes called lump breakers, can also be used for breaking frozen or agglomerated materials.

Williams Roll Crushers are used in a variety of industries such as, mining recycling, and power industries. Interested in learning more about the Williams Roll Crushers for your specific industry and application? Contact our sales engineers!

Choosing between a single roll crusher and double roll crusher depends upon the type of feed material, feed size, product size desired, and consistency of both feed and product. Both single and double roll crushers operate most efficiently with dry, friable materials. However, single roll machines have been widely and successfully used for the reduction of moist clays. They also have been long used as primary and secondary coal crushers, both at mine sites and power plants, where a minimum of fines is desired.

Williams single roll crushers reduce via a combination of impact, shear, and compression. The rolls are always toothed in patterns suited to the feed material. Single Roll Crushers generally handle larger feed sizes at higher reduction ratios in higher capacities and are particularly well suited to be used as lump breakers.

Double roll crushers reduce primarily through compression, although some shear is obtained with toothed rolls. Rolls for these crushers come in combinations of smooth, corrugated, and toothed designs. Double Roll Crushers produce a finer product at lower reduction ratios and capacities.

Oversized, heat-treated, alloy steel shafts plus self-aligning, roller-type bearings assure long life and maximum use of power. Jackshafts for control of roller speed are standard on double roll crushers, optional on larger Single Roll Crushers.

Heavy-duty compression springs permit movement of floating roll to pass tramp metal and other uncrushables, avoiding overload and damage. Smaller Single Roll Crushers are equipped with a shear pin release.

Faces Tooth patterns and corrugations to fit feed material; abrasion-resistant alloy; easily replaceable. Ash Crushers have additional features including dust-tight design and sealed cover plates for breaker plate access.

Williams Single Roll Crushers are also available in a 15 inch (381mm) diameter dust-tight version for applications such where it would be expensive to have dust collection air. Already well known for rugged construction, low profile, high reduction ratio, and economical cost, Williams Dust-Tight Ash Single Roll Crushers also have easy access to the rotor for maintenance. These dust-tight roll crushers are perfect for applications such as crushing ash, limestone, coal, or glass.

roller crusher double toothed roll crusher roller crusher for mineral coal equipment plant - best stone crusher plant solution from henan dewo

Dewo machinery can provides complete set of crushing and screening line, including Hydraulic Cone Crusher, Jaw Crusher, Impact Crusher, Vertical Shaft Impact Crusher (Sand Making Machine), fixed and movable rock crushing line, but also provides turnkey project for cement production line, ore beneficiation production line and drying production line. Dewo Machinery can provide high quality products, as well as customized optimized technical proposal and one station after- sales service.

Do you know toothed roll crusher machine? Toothed roller crusher vedio. Toothed roll crusher is widely used in coal, metallurgy, mining, chemical industry, building materials, and other industries, and it is more suitable to crush coal in large coal preparation plant and process waste. Toothed roll crusher has a high crushing capacity.

Double Roll Crushers. Double Roll Crushers provide a 4:1 reduction ratio. They are typically used as a secondary or tertiary crusher for materials such as ROM coal with refuse, limestone, gypsum, trona, shale, bauxite, oil shale, clean coal, coke, salt, quicklime, burnt lime, glass, kaolin, brick, shale and wet, sticky feeds.

Due to easier damage of the roller tooth for crushing hardness materials, it is not recommended to crush the raw coal with hardness gangue. The single-toothed roll crusher is applied for primary crushing with the characteristic of large feed granularity, and the double-toothed roll crusher is mainly applied for medium crushing with higher ...

Double roll crusher features a two roll structure with smooth surface. Teeth Roll Crusher. Teeth roll crusher is available in two roll and four roll series. According to the characteristics of material, coarse and fine teeth can be chosen. Four roll type teeth crusher is actually made up of two double roll teeth crushers.

Advantages of Double-Roller Crusher 1. In the production, the crushing range of double roll crusher is wide. Whether it is coal or large ore, as long as the material with Mohr hardness below 9 can be crushed by this machine. 2. The speed of finished products of toothed roll crusher is extremely fast.

Double Roller Crusher. Processing ability: 10-85 t/h. Brief introduction: Double roller crusher is mainly used for secondary and fine crushing materials with soft or middle hardness like coal, coke,limestone etc. Email: [emailprotected] Tel:

Double Roll Crushers. Double roll crushers reduce primarily through compression, although some shear is obtained with toothed rolls. Rolls for these crushers come in combinations of smooth, corrugated, and toothed designs. Double Roll Crushers produce a finer product at lower reduction ratios and capacities.

Crusher, Double Toothed Roll Crusher, Roll Crusher manufacturer / supplier in China, offering 2pgc Double Toothed Roll Crusher for Cement, Coal (2PGC900X900), Large Capacity Steel Slag Cone Crusher for Iron Ore, Newest Technology Cone Crusher Stone Crusher Price and so on.